similar to: Zaphfc.ko module error

Hi, I had problems described in another thread so went from a start, but now have problems when loading qozap module. I get : # insmod qozap.ko ports=9 insmod: error inserting 'qozap.ko': -1 Unknown symbol in module and in /var/log/messages: module qozap unsupported by SUSE/Novell, tainting kernel. qozap: disagrees about version of symbol zt_receive qozap: Unknown symbol zt_receive

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

Hi, Sorry to re-post, but I'm still having hassles with ztdummy. I'm using kernel 2.6.11.4-21.7-smp and Asterisk 1.0.8 on SuSE 9.3 The first 3 makes (see below) for zaptel work out ok - but the ztdummy.ko (etc) files *are* created even though I haven't yet uncommented ztdummy in Makefile. If the ztdummy bits are compiled, why edit Makefile & run make again? modprobe ztdummy

I'm chasing down a pop/click type of disturbance on a PBX system. Strangely, the disturbance is only heard by the outside caller, the internal recipient hears the caller crystal clear. This seems to have crept up when upgrading the zaptel driver to the 1.2 series while running 1.0.10. I went ahead and upgraded the entire system to 1.2.4. The system is a ~2Ghz AMD 32bit system, with 512MB of

Hi, I've compiled Asterisk cvs stable (few days ago) unde Suse 9.2 without any problems. We're using te110p and wcte11xp module that is autoloaded by Suse 9.2. Card goes green after reboot, but this meesages appear in logs: Mar 22 11:28:51 linux kernel: Zapata Telephony Interface Registered on major 196 Mar 22 11:28:51 linux modprobe: FATAL: Error inserting torisa

I got a new motherboard and upgraded Asterisk, ... However, I am not lucky enough to get it running again. To compile went ok, besides this remark at the end of asterisk: WARNING WARNING WARNING Your Asterisk modules directory, located at /usr/lib/asterisk/modules contains modules that were not installed by this version of Asterisk. Please ensure that these modules are compatible with

-----Ursprungligt meddelande----- Fr?n: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] F?r Terry Wade Skickat: den 19 augusti 2005 07:08 Till: 'Asterisk Users Mailing List - Non-Commercial Discussion' ?mne: RE: [Asterisk-Users] Zaphfc.ko module error Hi Remco Thanks for the response. I am running Suse 9.3 kernel 2.6.11.4-20a-default. Will check

Hi to everybody, seems that I cannot load the zaptel modules: ztdummy says the following: [root@Hayabusa misc]# modprobe ztdummy /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_unregister /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_transmit /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_receive /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_register

I get this warnings while compiling zaptel Any suggestions would be very helpfull. make -C /usr/src/linux-2.6 SUBDIRS=/usr/src/bri-stuff.0.1.0-RC4/zaptel modules make[1]: Entering directory `/usr/src/linux-2.6.8.1' CC [M] /usr/src/bri-stuff.0.1.0-RC4/zaptel/zaptel.o /usr/src/bri-stuff.0.1.0-RC4/zaptel/zaptel.c:163: warning: `fcstab' defined but not used CC [M]

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031223/62cf404e/attachment.htm -------------- next part -------------- Hello When I tried loading TDM400P module using insmod command, I get following error messages. Is there some problem with my asterisk installation. Please advise. Thanks Tony $insmod wcfxs Using

I downloaded the cvs development of zaptel... It seems to compile ok, but when ismod I get: lp:/usr/local/src/zaptel# /sbin/insmod wcfxo.o wcfxo.o: unresolved symbol zt_ec_chunk wcfxo.o: unresolved symbol zt_unregister wcfxo.o: unresolved symbol zt_alarm_notify wcfxo.o: unresolved symbol zt_hooksig wcfxo.o: unresolved symbol zt_transmit wcfxo.o: unresolved symbol zt_receive wcfxo.o: unresolved

You where SOO right. My idea is to connect the "line" to my pbx and call from internet (h323?) to my linux box, and then dial an extension.. Is there any doc there? Cause Ive read a few and I did not get much really. I should configure asterisk now and the job is done? -----Mensaje original----- De: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] En

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o

Hello, I am trying to install the drivers for the Junghanns quadBRI card, but am having a problem. I have essentially followed the procedure from http://www.voip-manager.net/installation-linux-asterisk.php. At the stage to install the ISDN card I have completed the following: 1) downloaded the bristuff-0.2.0-RC8q.tar.gz to /usr/src 2) unpacked it in /usr/src - tar xvzf bristuff-0.2.0-RC8q.tar.gz

Hi, >However, I believe that zaptel >= 1.4.6 or zaptel 1.2 >= 1.2.21 should >support hires timers for timing on kernel >= 2.6.22 . > >What version of Zaptel do you use? > I was using version 1.4.5.1 I just downloaded and installed version 1.4.7, configure/make/make install finished without an error, but when is used modprobe ztdummy the system said: FATAL: Error

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

Hello all, I am planning to setup a MeetMe conference functionality on Asterisk-1.4.13without having a Zaptel card. All users will be calling through SIP only. AFAIK, the said application needs a timer which makes use of the ztdummy module. I have basically two (2) problems I am encountering here that [1] I can't load the ztdummy.ko module and [2] Asterisk don't run when running it

I would like to know how to install asterisk 1.0.9 with zaphfc working on a SuSE 9.2. I tried this: - The rpms with SuSE 9.2 are asterisk 1.0.6 - bristuff works, except for zaphfc, which doesn't compile. - The official asterisk download file doesn't contain isdn bri support Any ideas? Lars Dybdahl.

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk