similar to: TDM400 on BT network in UK

So I have an application where the users want to divert incoming calls on one analogue line out to another analogue line - both lines are supplied by BT and theres a TDM400 in the box. Call comes in, system Dial's the forwarding number and bridges the calls. Works fine. Until one (or both) leg hangs up. And the box never sees the hangup. So it sits there with both Zap channels open

Hi all I'm using sangoma a200 cards in the UK and have the ongoing, often noted problem of disconnect supervision with BT POTS lines. Just noticed this post on http://www.voip-info.org/wiki/view/UK+Asterisk+Details stating that potentially someone's got a solution : "TDM400P & Not Detecting Hangups: Got a TDM400P installed and having problems with Asterisk not detecting

Andi - I have experienced the same issue you mention and gotten no reply as to a way to fix it. I finally implemented "blacklist" into my Asterisk and added "Anonymous", "anonymous", "unknown", "Unknown", etc., into my blacklist file. When those come in with an IP address instead of a phone number but have no real name, they get the

Have anyone tried to interface BT's Broadband Voice with asterisk? Kannaiyan

When a caller hangs up (e.g. after leaving a voicemail), my British Telecom exchange sends a continuous tone for about 15s and then silence. I can't get asterisk to recognise this tone as a hangup indication. I have tried indications.conf with both country=uk and country=us. My zapata.conf has busydetect=yes, callprogress=yes and I've tried setting busycount from 1 through 7 I am using

Folks, I have a TDM400 with an FXS module. I'm having some trouble ringing some phones attached to the device. I have a real el cheapo handset that cost me about 9UKP. It works fine, I plug it into the Wildcard and call the channel and it rings. I have tried plugging in my BT Diverse 3016 cordless phone but it will not ring, although I can call out from it. I have also tried my GPO 332L

Hi all, We have tested both tdm400 and BRI 1 port HFC based with mISDN driver and with both cards we have the same problem... so probably it's due to our misconfiguration, but we couldn't find anything useful on google. With TDM400 we can place and receive calls, but if we receive a call from TDM400 and we reject it from a sip phone , asterisk send the hangup but the line continue to

Hi there Just a general question, has anybody experienced any problems with any Digium telephony cards in the UK, specifically with BT (British Telecom) lines. I just want to make sure there are no compatibility issues before purchasing cards, (mainly TDM400P's) Any comments would be greatly appreciated Thanks

Hi, We've got troubles trying to connect a Brother 8360P to a TDM400 FXS board. Design is : PSTN ------ Junghanns QuadBRI --------- Digium TDM400 ----------- Brother fax As you can guess, QuadBRI and TDM400 are plugged into 1.0.10 Asterisk server. - from Asterisk console, we can observe calls reaching the fax machine but the fax never answer - when we substitute the fax with an analog

Hello, I'm not detecting caller Id through DTMF with my TDM400 card and don't know how to put this to work. Could someone please help me ? How should I configure * to achieve this? Thanks, Fernando

When configuring a TE410P which is only attached to a single E1 together with a TDM400, how should one count the channels for the next Zap interface? Must I put 4 span lines in zapata.conf and define all channels up to 124? thus having the TDM400's start at 125? Or can I comment out the 3 spans I don't use and start at channel 32 for the TDM400? (this would get nasty when adding extra

Hi, all Did anyone tried TDM400 card on old main board (Intel 440LX chipset -- PII)? The reason I am asking is because TDM400 needs PCI2.2 and main board is PCI2.1 I do not want to upgrade yet. Thanks, Rudolf

Hello, I have the following configuration : E100P -> * -> TDM400 -> Modem When I receive FAXes, about 20% of them are corrupted : pages are not always complete. If the fax is complex or with numerous pages, it's usually a mess. Before that, I was using spandsp with success. Unfortunately it's too picky with some broken fax (training failed). Since this failure only occurs with

Hello, I have a TDM400 with 2 FXS modules and 2 FXO modules, as follows: Zap/1 - internal phone Zap/2 - internal modem Zap/3 - exchange Zap/4 - exchange Recently I upgraded zaptel (and kernel modules) from 1.0.9-1.1 to 1.0.9.1 and upgraded asterisk to 1.0.9.dfsg.1-3, which are Debian versions for Debian/sarge of the packages I believe the Debian maintainers created (not in Debian) The above

Hi all, I just got my long awaited FXS modules for a TDM400 card, and was a bit puzzled about how my phones and the FXS interface worked together. Here goes: In Sweden (that's where I am located) phones traditionally are connected in daisy chain configuration. This means that a phone in on-hook condition passes the line through back onto the outer pair of the RJ11, back into the wall

as the subject states I have a TDM400 that when a call is answered asterisk runs the dialplan even if i hang up it NEVER detects the hangup and I am also having a hard time with CID info I don't get that either. most of our production machines are PRI based and I have little experience with the TDM400 cards, ANY help would be appreciated. Thanks in advance!

Hi, I have an TDM400 4 FXO module setup on my dual Celeron server running asterisk 1.0.2 and I have had to restart the asterisk process multiple times lately. I was wondering if anyone else has to restart the asterisk process after storms roll through their area. Before I restart I usually have sound quality issues and weird pickup problems. But, once I restart the asterisk process everything

Folks, I recently swapped a TDM400 FXS card that was working perfectly into a new server (running recent CVS), and it's either misbehaving (unlikely), or I've missed something obvious (much more probable). Everything seems to be working, but I can't get any dialtone from it when I plug a phone into any of the 4 ports!! All of the jacks are lit (green lights) but they all seem dead

Today I had channel 1 on my TDM400 go to sleep, verified by pluggin in known good telco lines in various combinations on channel 1 through 4 - problem is channel 1, not anything external. So after seeing lots of stuff on the list re: TDM400's I power cycled, removed board and let linux say nothing's home, replaced board, told linux to ignore it etc. No OS/asterisk/etc changes made on

And if that ain't confusing I don't know what would be. I bought a TDM400 with two modules (FXO, FXS) a couple or so years ago and ended up never using it. Passed it along to a friend who is having some problems with it. (He isn't on this list.) We've both tried searches using Google but haven't been able to find anything that helps. So this is more a question of