similar to: Is it mandatory to give power supplytoTDM400Pcard

Has anyone come up with a way to get power to a TDM400P card installed in a Dell PowerEdge 1750? Thanks, Adam The contents of this email message and any attachments are confidential and are intended solely for addressee. The information may also be legally privileged. This transmission is sent in trust, for the sole purpose of delivery to the intended recipient. If you have received this

does TDM2400 work on 3.3v pci slot? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070211/ac7d0c79/attachment.htm

Hello - I've been running Asterisk (quite happily!) for several years now using a Digium TDM400P card in an old Linux box (P4 1.6 w/ 256MB RAM). I'm also running another old PC running m0n0wall as a firewall. Between these two boxes, that run 24x7, I'm drawing a lot more power than needed and hoping to make a dent in my monthly electric bill by consolidating the two into a single box

That was my thought too. Even if it *does* work without it, there may be a reason internally you can't see why it is required. (Ex. Putting extra stress on a component causing it to fail in 6 months) -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Tom Rymes Sent: Wednesday, August 10, 2005 3:49 PM To:

Is it not for a card with 4 FXO? I spent several hours the other day trying to figure out what I had done wrong and I ahd forgotten to connect the power cable. I setup several of these before and couldn't figure out why this one didn't work. It appears that's all it waqs. Without the power connecter the card will probe, and even appear to be working but when the lines ring (coming

Hi recently bought a soekris net5501 and a tdm410 to place in there. I am having some issues attaching 12V power to the card via the molex card - basically the box for the motherboard is too small. I have read up about a PWR2400b and it seems to use 2wire pin, I am guessing to connect to P8 just behind the molex connector on the tdm410. can any one here confirm this, or have any info on the

http://www.mixdown.ca/~asterisk/ The card seems to be working fine. Don't expect warranty on it though. :-) Why? Because I wanted a quad-span T1 card which worked in the high-end systems I was intending it for, but that I could also keep a few in stock and if the system mainboard failed, pull the card an put it in a standard PC system. I didn't want to have to stock 3.3V and 5V

Hi, I just bought the E100P from digium. It has both keys: 3.3V and 5V, so it would fit both, in a 5V-PCI slot and in a 3.3V PCI slot. Is it true, that I can plug it without destroying it in an ordenary 5V PCI slot? Roger.

Anyone have a suggestion on where I can get a decent new MB with 5v capable PCI slots. It seems like every decent server MB on the market has 3.3V slots only. Is diving into the junkbin my only choice if I can't afford to replace the 5v quad-T1 wildcard? Thanks Mark Farver

Hi All, I've just started caring for a dual Opteron machine. It has a 3Ware 9500S-12 RAID controller, a Tyan S2882G3NR motherboard, 10 IBM 400GB disk drives, and a 650 watt power supply. It has been behaving itself quite nicely until recently. The poor behavior started when I upgraded the OS from CentOS 4.1 (32 bit) to Centos 4.1 (x86_64). When running in uniprocessor mode, the system

Hi I've a Sangoma A200D with 2FXO and 2FXS. When using it with only the FXO module, it's all good. But when I put in the FXS module and connect the power, logs tells me not enough power. > Mar 31 14:11:54 phone kernel: [ 4761.246931] wanpipe1: Module 1: > Failed to powerup within 600 ms (8V : 72V)! > Mar 31 14:11:54 phone kernel: [ 4761.246937] wanpipe1: Module 1: Did

Below is a snipped debug on our PRI. We are getting number only for the CallerID but the telco says they are sending us Name and Number. We are getting the Name in a second frame but Asterisk is not passing it to the device it rings. The message below says "Presenation allowed of network provided number" which leads me to believe Asterisk thinks it should not be displaying it. Can anyone

Hello, Digium uses the Dell PE 2850 for their testing. This site says that 3.3V PCI slot. http://www.voip-info.org/wiki/view/Asterisk+hardware We are planning on purchasing a Dell PE 2850 and putting a TE205P card on it. However, the needs a 5V PCI slot. Does Dell PE 2850 has a 5V PCI slot? A person in our group tried to call Dell's customer support but they do not seem to know.

The only phones I have much experience with are the sipura spa-841's, the netweb 301/302 phones (which I really don't like) and the polycom 300/301's. It applies to the sipuras and the polycom's for sure. I can't remember about the netweb, we quit using them sometime last year. -Jonathan -----Original Message----- From: asterisk-users-bounces@lists.digium.com

Here is my file to parse and load extensions. No wise cracks about my code.... DB.php is the Pear DB module. (pear.php.net) <?php include('DB.php'); $db_host = ''; $db_name = ''; $db_login = ''; $db_pass = ''; $db_table = 'extensions_table'; define(DBINFO,"mysql://$db_login:$db_pass@$db_host/$db_name"); $db =

Lately I got (used) an APC Back UPS Pro 1000 and Back UPS NS 1080. I got an ethernet-to-USB cable from another UPS, but the Pro isn't detected (with usbhid-ups.) I haven't tried the NS yet but it seems to not be on the list though looks just like the Pro. Some months ago I was discussing setup of a Ferrups 700VA.  I got it to work only with a command in rc.local, but not automatically

Can anybody tell me the difference between a TE410P and a TE405P? Is it JUST the 5v vs 3.3v pcis slot spec, or is there some thing else? </edg>

Is anyone using a net4801 and an analog only setup? I am looking for a modem that is PCI 3.3V, apparently the X100P is 5.0V PCI only so it won't work with the net4801.

I am having a issues with adding a analog card to my dell 2800. I already have a t1 card installed and running fine but when I install the analog card asterisk will not start (ztcfg fails). I have determined it is because of a IRQ problem and have decided to get a new server. Can anyone suggest a server grade setup that supports this? I would rather not buy a machine that will be unstable. I

Hi All. Yesterday I was installing Centos 5.5 to my web server, and it looks like the main hard drive has gone AWOL. Fedora 12 put the file system into r/o mode. The drive is an Hitachi, still under warranty. There are bad sectors on it, and running the Hitachi DFT tool confirms this. Also I cannot repair the bad sectors. Would this be caused by a faulty I/O chip, or is it safe to say