similar to: RE: Info / recommendation on either Audiocodes or Vegastream gateways

Greetings; We are trying to get Asterisk up and happy at our site-we tried VOIP using Sphere about a year ago, spent a *boodle* on expensive hardware and services from a local "expert", but it never was happy. I'm brand-spanking new at VOIP, and I've learned a *ton* getting Asterisk breathing in the last couple of days. I have three Polycom Soundpoint IP 500 SIP phones, which

guys, what firmware version of audiocodes mp104 fxs are you using with asterisk? i'm having sip stack problems. ~kelvin -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030916/50d5f5de/attachment.htm

hi, i've successfully configured 2 audiocodes mp104 fxs and fxo configured using SIP with asterisk currently i want to add another 2 boxes of audiocodes mp200 to add up a total of 4 trunks how can i combine this mgcp to run together with asterisk SIP? Thanks in advanced Steven

We're trying to use some AudioCodes MP104 FXO units as gateways to Asterisk but cannot get them to reliably detect DTMF. Some landline calls get most digits but some are duplicated. Some cell phone calls get 0% DTMF recognition. Anyone with experience with these units have any suggestions? ABP Technical Support has been unable to diagnose the problem and is now sending random guesses and

We have a Vegastream 400 connected to a digium Quad PRI card in an asterisk server, for the T.38 faxing here. Problem is that there are too many clockslips on it (and they get logged by asterisk as HDLC aborts). I've double checked the configuration on both sides, replaced the cable, tried different ports etc. It all lead to no resolution for it. Is there somebody on the list who has a

I wonder if anyone can help me? Am trying to terminate to H323 Vegastream. I'm using OH323 with little success. I can dial out and answer but voip end just keepings ringing and ringing. Thanks for any help. Neil Config file: [general] listenAddress=ALL listenPort=1720 tcpStart=10000 tcpEnd=20000 udpStart=10000 udpEnd=20000 fastStart=no h245Tunnelling=no h245inSetup=no jitterMax=100

I am trying to solve the fax problem by installing an E1 channelbank (Megaplex MP-104) It's a box that has 8 x FXS ports and a single E1 port. The plan was to use one of my 4 E1 ports to connect to the Telstra onramp and one to the MP104. I have since discovered however that the MP104 only supports CAS signalling and I am having trouble getting asterisk to work in this mode. Currently we

I'm trying to connect this FXO GW without any success 1) I had to configure the " " to "allow any SIP to connect , so there will be a connection. afte that when I'm dialing I get a noise. I read on the internet that I have to change the impedance (?) 2) I could not find any HOWTO configure this combination - I read that it is a lot of pain to configure the Mp10x but than

Hi all, I want to link three incoming Bell Canada centrex pstn lines (which currently go to an old norstar pbx) into asterisk. Can anyone suggest the most "painless" (i.e., "just works") way to do this? Has anyone used the D-link DVG-3004S four-port FXO-to-sip adapter, or the twice-as-costly Audiocode MP104-FXO-C3S? I know the Digium TDM400P or Sangoma A200 are options

Hi list, any one can let me his config files for interconecting a Meridian Op 11 and Asterisk via a E1 PRI CARD. Actually i need the nortell config part, becouse my client nortell provider doesn't know how to config the PRI card at his part. Thanks all. -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am trying to configure a VegaStream 50 FXO to work with asterisk. The problem that I am having is that the VegaStream does not support incoming registration from asterisk. VegaStream only allows outbound registration. My question is does asterisk allow incoming registration from an FXO? If yes how? Or better yet, has anybody been able to make the VegaStream FXO work with asterisk? According

Hi list, I'm trying to get ready the MP-104 FXO to use qith my box, but when I send calls I hear only dial tone and after a few seconds I get busy signal. I very appreciate your advices. Command line results and SIPconfigurations follows: *CLI>* -- Executing [7991696900 at total:1] Playback("SIP/101-09dd8918", "beep") in new stack -- <SIP/101-09dd8918>

Hi all, I'm new in the forum, and although I have some experience in Asterisk, I've never work with Asterisk FXO, FXS, E1... cards. I have several costumers with ATAs working with my SER. However one of them bought an Alcatel PBX OmniPCX Enterprise and now he wants I give him a E1 interface for interconection with its new PBX. I understand I need a E1-IP gateway which could be Asterisk

My experience with an MP-108 was similar. Incredibly complex to setup, and very little help from MFR, or even ABPTECH, the main US reseller. We just couldn't get it working properly. Ended up with a TE110P with an Adit 600 channel bank, which ROCKS. Unbelieveably easy to setup. No echo whatsoever. -Darren

Sorry for the very newbie-like question. I have the FXS part straight. The part I don't understand is the FX0 part. Will I need the FX0 card if I am connecting to a service like FWD? My goal is to get rid of my phone line all together. I am under the impression I will only need an FX0 if I'm connecting to the central office side of the phone connection or to an existing PBX. Bottom

I have a couple of devices that need an analog modem to communicate outside of our Asterisk system. Most FXS gateways don't seem to support this... I have a stack of Sipura 2002's that are, AFAIK, worthless for this purpose. I've heard that Digium's IAXy FXS will work with modems, but I can't find any reference to that in their documentation. There is also the

I have an Audiocodes MP-118FXO in production. When an outbound call is made and the remote party hangs up, the Audiocodes hangs up the call immediately. But if an incoming call is received and the remote party hangs up, the Audiocodes does not hang up immediately. I have tinkered with Current Disconnect and Polarity Reversal settings, to no avail. Anyone experienced this issue with Audiocodes or

I have an Audiocodes MP-114 and modem dial-out can not establish connection. Snooping with Wireshark I get a lot of entries like this: No. Time Source Destination Protocol Info 2934 27.221559 10.0.0.110 10.0.0.109 RTP PT=ITU-T G.711 PCMU, SSRC=0x7D08611A, Seq=7662, Time=1805957855 Frame 2934: 214 bytes on wire (1712 bits),

Hi, This is my first experience with a mediant 1000 and an Asterisk Trixbox. the mediant has 12 FXOs and 12 FXSs, and I want to use it them all. I will have extensions connected to the FXS ports, and lines to the FXO. Can anyone guide me, please? regards, -- Guillermo Garron "Linux IS user friendly... It's just selective about who its friends are." (Using Ubuntu, Debian,

I have an MP114 2fxs,2fxo which I would like to use with Trixbox, does anyone have a setup file they can share to help me work this out. Instructions or a link I can follow - thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20090726/643e5b96/attachment.htm