similar to: TE110P flashing red/green when PRI connected

Perhaps everything isn't as spiffy as I thought When running zttool the card still reports as internally clocked Zaptel.conf: # Global data span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 loadzone=se defaultzone=se And as pointed out by Peter I do get a lot of D-channel warnings ... Aug 9 16:21:25 NOTICE[1350]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 And

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you

I have an Asterisk server that was running fine until Sunday. Monday there was a power outage and the server was off most of the day. This server has a TE110P, two TDM04B and an Astribank 32. Today I noticed that the TE110P started having IRQ missess. Before today it only had about two or three per month. Today, this is the miss count after ten minutes on: IRQ Misses: 1443

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hi, we've installed te110p with Suse 9.2 on Siemens primergy. We're connecting to voxsteam i60 to test PRI interface. We have problems, after reboot sometimes it goes green, otherwise stays blinking red. How could we debug this situation ? Are there any common advices what to check ? Are CVS Head drivers better than CVS stable ? Why ? Do you also experience such unstable behaviour

Does anyone know if you can have multiple TE110P cards in one chassis? -Thermal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061011/adbceeb5/attachment.htm

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco

I have a Digicom TE110p card installed in our exchange. I have compiled and installed libpri, zaptel and recompiled and installed asterisk. I have configured udev as I am running Fedora Core 3. The problem that I have is that when zaptel is not running everything works fine. However when I start zaptel (service start zaptel) then I can make normal calls ok but the 'Playback()'

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18

Hi everybody, i need someone to tell me the spins numbers of Rx+,Rx-,Tx+ and Tx- of TE110P and also if you can tell me have to made a cable like that?? Modem Teleco <-----------Self Crosscable------------>Asterisk Rx+ <--------------------------------------------------------------> Tx+ Rx- <--------------------------------------------------------------> Tx- Tx+

Hello all, Has anyone use the Supermicro PDSME+ in combination with the TE110P successfully? My experience so far is not very good. I am running trixbox 2.0 but: 1) with zttool I am getting IRQ Misses. Don't seem to have IRQ conflict, but I am now running my SATA HD in DMA. And I am not able to set it in DMA(HIO... operation not permitted) 2) With zttool the Alarm is RED 3) When I do the

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Ok I F@%& up. I didn't realize the card is 3.3 volts and my new computer is 5V. Can anyone point me to a PCI to PCI bridge. Any suggestions? Mike

Running Asterisk 1.2.9. I just installed a TE110P card and configured zaptel.conf & zapata.conf. The config files look right to me but I'm getting the following error when trying to start asterisk: Asterisk died with code 1. Automatically restarting Asterisk. Does anyone have any idea what is wrong with this configuration?? Thanks in advance!!! Here's my config files: zaptel.conf

Hi list, I have a terrible noise issue with Dell SC1430 + Digium TE110P. The digium card is not sharing interrupts with any other device, as I saw in Dell's BIOS and also with "lspci -vb" command. After changing coax wire, UTP, balum, digium card ... I have found that the problem is in Dell box, so now I'm running the same Asterisk config in other server with the same

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi All Before I go out and buy a DELL PowerEdge 2850 has anyone had problems (or any other useful experience) getting a TE411P to work with it. I also have a legacy TE110P. Has anyone had problems with this combo. -- Dr. Rodney G. McDuff |Ex ignorantia ad sapientiam Manager, Strategic Technologies Group| Ex luce ad tenebras Information Technology Services | The

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]