similar to: Some echo?

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

Hi steve and All, I'm attaching cat proc/interrupts out put, lspci -bv out put, zapa.conf, zaptel.conf for your information Thanks so much for the feedback and I do accordingly. Hope to get rid off this isue any how. To day also reported 10 call drops within 2 hours of period. fook forward to have your support on this regard. Thanks & Regards, Vidura Senadeera, Network Engineer,

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

Hello List, i am trying to set up an * box with a debian 2.6.10 Kernel. the compilation of asterisk and the zaptel drivers worked almost perfectly. so i did modprobe zaptel modprobe wcte11xp (which is the correct driver for my card) ztcfg -v and this results in ZT_SPANCONFIG failed on span 1: No such device or address (6) I don?t have any ideas whats wrong. google was no help, checking sources

While testing a problem with "spontaeously" and "occasionally" rebooting asterisk, I came upon this problem: Program received signal SIGSEGV, Segmentation fault. [Switching to Thread -1210770512 (LWP 11346)] 0x002e3fe1 in pri_release_timeout (data=0x93a0478) at q931.c:2589 2589 q931.c: No such file or directory. in q931.c q931.c is in libpri, function

I've been going nuts lately trying to get rid of an annoying echo problem that makes my asterisk server unusable when clients try to call me. Here's the breakdown of the issue - Hoping that someone can throw me a clue: My setup is as such: Single AMD Athon machine with X100P clone card and voip through multiple providers . * Inbound calls through the X100P that do not bridge to

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

I currently have two channel groups in my zapata.conf file. I would like one group to be immediate=yes and the other immediate=no Does not seem to matter which way I go, the first entry in overrides my explicit setting for the second group. I am running * 1.0.9 on FC1 [trunkgroups] ;trunkgroup => 1,24 trunkgroup => 1,48,72 ;spanmap => 1,1,0 spanmap => 2,1,0 spanmap => 3,1,1

We're rolling out Cisco 7940 phones, linked to *, which is running a TE405p EuroISDN. We have 2 ISDN lines, one we had for testing, and one for general (40+ users) use. During the testing phase, we had 10 phones linked to the second ISDN line, and there were no problems with echo at all. Lucky me. However, since we have started rolling out, we've had quite loud complaints that there is

I am trying to place an analog outbound call from a Sipura SPA-841 through a * server with a TDM400P and 4 FXO's. When I call in from an analog line everything works fine, I can talk over the SIP phone. When I call out, * says: == Spawn extension (from-sip, [phonenumber], 1) exited non-zero on 'SIP/sipphone-d29d' -- Executing Dial("SIP/sipphone-9eb0",

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

Hello All I'm using asterisk 1.1.X and MFCR2 lib version 0.03pre2. when i call to E1 (connected with asterisk), chan_unicall don't detected event incoming call and show error. error messages: *CLI> Warning, flexibel rate not heavily tested! Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 4 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2

Deat all, I am in middle of integrate Asterisk with Toshiba astrata legacy pbx. Following is my setup *Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX* A =============================================> B C <============================================ D Asterisk PBX and strata PBX connected using back to back E1 cross cable. Physicall connectivity

I have NFAS setup on several quad port T1 cards (Sangoma). It mostly works well with the exception that calls coming in on channels 48,72, and 96 have no audio. I tried removing these channels from zapata.conf with hopes that the channels would not come up or be used. Now I get "Ring requested on unconfigured channel". How can I busyout these these channels so that incoming

Hello, I have some problem to start asterisk. First I have followed a lot of tutorials to complete correctly the install process. Now it works when I type zttool I can see when I am or not connected to the PSTN. But, I run asterisk with vvvv verbose and I can't see the call detection. There is no detection of the call. I have a X100P card FXO with only one line. So only one channel I

Hi All i'm using sangoma card. connected to E1, my wanpipe file as #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Fri May 27 00:25:04 GMT+7 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it