similar to: MFC/R2 Mexico Unicall Blocked

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Hi all, I still haven't seen my first post (cry for help) so I'm not sure if these are going through or not ... I've played with the box all day today ... I got it to quit seg faulting finally by playing with the config files. Currently I have 4 spans configured for a Digium TE420B (With Octastic DSP) Here is my zaptel.conf: (I know the device connected to spans 1-3 are providing

Hi everyone! I'm having some issue trying to place calls with asterisk connected to an E1 R2 from Telmex Argentina. The other E1 port is connected to a Meridian which also uses R2 protocol. Calls sometimes fail with different error messages such as: Unicall protocol error 32773, 32772, 32769. Some other calls fail saying: Far end disconnected(cause=Destination out of

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hello, i'm using asterisk 1.4.9 in fedora 7, i was compiled its with this package: libpri-1.4.2 asterisk-1.4.9 spandsp-0.0.4 unicall-0.0.5pre1 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 zaptel-1.4.4 i'm using a E1 pci card with R2 but they not work, when I start the asterisk its generate this log: [May 12 08:53:24] WARNING[30814] channel.c: No channel type

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but

I followed the how-to for R2 that coppice wrote on the webpage http://www.opencall.org/installing-mfcr2.html, now asterisk has channel unicall and when i test an incoming call I get the following errors. astbox:~/mediatel/libmfcr2-0.0.1# asterisk -r Asterisk 1.0.0, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com>

Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

Hi all. When I place a call Im getting this error: Jul 25 09:50:07 WARNING[3200] channel.c: Exception flag set on 'UniCall/13-1', but no exception handler Lots of this messages appeared on my Asterisk full log and the CPU got 100%. Topology: Analog Phone - Hicom300H E1 - E1 Asterisk - IP Trunk Problem: 1. Calls from Analog Phone through Asterisk is ok, but the messages appeared.

Hi. I am in the Brazil. I have a problem on Unicall for Asterisk 1.4. I am working with E1 with 30 channels. Message when it receives calls: chan_unicall.c:2603 handle_uc_event:unicall/1 protocol error.cause 32772. My files: /etc/zaptel.conf: span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 loadzone = br defaultzone = br fxoks = 32-55 /etc/asterisk/unicall.conf: [Channels] language=br

Hi all, any body can tell me why i am receiving this message in my sever ? I have running * with 10 Digital Lines, but i am receiving a lot of times this message . Is a software issue or is a hardware issue ? Regards. Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:2672 handle_uc_event: Unicall/5 event Alarm Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:3091 handle_uc_event: Unicall/5 Alarm masks

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Dears, After having set up the board Digium TE420 to receive 3 E1s, I can receive calls without difficulties. As you can see in the log below: -- Executing [5908 at from-pstn:1] NoOp("UniCall/14-1", "Catch-All DID Match - Found 5908 - You probably want a DID for this.") in new stack -- Executing [5908 at from-pstn:2] Goto("UniCall/14-1",

I don?t know if the last message was with content. So, I sent again. I have installed a Digium card TE210P and unicall for use MFC/R2. I think that it?s all right but I can?t make and receive calls. I?m using asterisk 2.1 with the patch made by Jos? P. Leit?o and the follow libs: libsupertone-0.0.2 libunicall-0.0.3 libmfcr2-0.0.3 zaptel 2.1 My number is 34318300. The Telco send me only 8300.