similar to: Polycom SoundPoint 600 : 10 seconds of delay when answering a call.

Hi all, I have a Polycom Soundpoint IP 600 that looks like it is fried. It either has a bad or corrupt bootrom (I'm guessing). It never gets to the prompt that asks if I want to enter the setup configuration or continue booting. When plugged into power, it turns on, shows the Polycom logo for 3 seconds and then pretty much goes dead with two red lights on. The one in the top right corner

What headsets have people found work well with the Polycom Soundpoint 500 & 600? If any of the headsets that work with the Polycom's also work the Cisco, that would be an added bonus, but is by no means a requirement. I am not looking for a headset that requires an external amplifier, but rather a headset that can make use of the headset jack on the phone itself.

Has anyone been able to get the minibrowser on the Polycom SoundPoint IP 500/600 phones working? If so could you share the relevant sections of your config with me?

Hi We've setup an Asterisk PBX recently and I encountered the following problem: When [mac address]-registration.cfg file includes the FQDN of the Asterisk PBX for the Polycom SoundPoint 501 phones it will not (even try to) register with the Asterisk PBX unless the DNS (it asks) successfully resolves the name: _sip._udp.[Asterisk FQDN]. Did this happen to anyone else? PS - The

I've got a couple Shoreline IP phones, their Shoreline model number is Shoreline IP 100. I believe this is actually a Polycom SoundPoint IP 300 phone. I believe the phone is using a MGCP stack. I want to use it for testing with Asterisk. 1. I suspect I need to re-image the phone to make it work with *. 2. How can I preserve the current image on the phone? 3. What is preferred image to use

Hi Folks; I just bought a Polycom SoundPoint 500 off of ebay after having spent way too much time trying to get updated sip images for our cisco phones. The phone I bought didn't have an AC power adapter; Could someone please tell me the volts & amps that the dc plug that comes with the phone puts out? Thanks! Mike

Hello all, I need the bootrom.ld file to set up some Polycoms I have Platform: Model=SoundPoint IP 330, Assembly=2345-12200-001 Rev=A I've publiched on my FTP files downloaded from http://support.polycom.com/PolycomService/support/us/support/voice/soundpoint_ip/soundpoint_ip330_320.html (3.2.3 combined and split zips) but my phones are still showing the message: "error, application is

I bought a couple Polycom Soundpoint 300's, and have them working nicely with SIP... but I'd like to be able to do automatic config via FTP, but it requires some XML config files. The docs discuss them in detail, but I can't seem to d/l them from Polycom. [No, it doesn't appear to be on the CD that comes with the phone.] I've created an account at Polycom's tech support

I am looking for clues on how to configure distinctive ring for a PolyCom SoundPoint 300. Does ALERT_INFO apply? If so, how? Thanks, David Koski david.nospham@kosmosisland.com

Hello! I am selling hardware I have been using in various Asterisk test installations. If you are interested in buying all or any of the following items please reply off list. I got a few * X100P clones * Sirrix PCI4S0 ISDN BRI cards (+ 1 Sirrix S0 voltage/power supply) * 1 Polycom Soundpoint IP 500 (+ Plantronics headset) * Conrad HFC-S cards to give away. Some of the pieces are unused,

We recently took a few Polycom Soundpoint IP 500 to test out in Asterisk environment. So far it has been good. Call Hold, Transfer, DMTF etc. However, I do notice every now and then the Polycom fails to register with Asterisk. Asterisk console outputs the following: Feb 3 13:02:32 WARNING[278546]: chan_sip.c:2365 __transmit_response: Unable to determine sequence number from '' Feb 3

I've looked all over.. I can only find the polycom soundpoint ip 300 w/ sip @ atacom but they're all out of stock. Any input would be appreciated.. Thanks.

Thanks, I was afraid to try and change gains that I didn't know what they did simply because I don't want to blow a speaker or something.. :) I'll try it today. The only thing I haven't figured out is how to set a default ringer in the configuration file, set my time to EST w/ Daylight Savings and when receiving incoming calls if it's possible to see NAME & NUMBER instead

If that was possible, that would make my life easier as well :) -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Michael Graves Sent: Tuesday, August 31, 2004 10:12 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Polycom SoundPoint... Gains - Whichis for speakerphone

I have a polycom soundpoint ip 501 phone I was having problems getting some of the functionality working like the **number to pick up calls to other phones then it just started working (when it couldn't update itself for a while) Unfortunately then I got that issue sorted and it updated to the latest firware and now it doesn't go again. Is there something in the config files themselves

Hello list, anyone have a manual for the webGUI of the above phone ? Just bought a Polycom Soundpoint IP300 and on the site of Polycom I see a user manual and a administrator's manual but none of these 2 guides explain the fields in the webGUI. Trying to understand the difference between the 'server-'variables in the 'SIP'-section and the 'server'-fields in the

Hi I'm new to this list, so please forgive me off-topic or RTFM-questions. I have an asterisk/elastix driven phone-environment using Polycom SoundPoint IP 650 as extensions. When adding just one custom ringtone (~57KB) in a proper format (ML.wav: RIFF (little-endian) data, WAVE audio, ITU G.711 mu-law, mono 8000 Hz) the phone boots well. But after I have chosen the custom ringtone as my

John, By chance do you know how to set a default ringer? What I have done is the following: <DEFAULT se.rt.1.name="Default" se.rt.1.type="ring" se.rt.1.ringer="7" se.rt.1.callWait="6" se.rt.1.mod="1"/> As you can see, I want 7 to be the default ringer for line 1... For some reason, it doesn't take these changes.

I'm attempting to set up my SoundPoint 501 with my Asterisk server. I've configured DHCP and TFTP and successfully updated both the BootRom and SIP application. I've also created a custom cfg file for this phone's MAC address and the settings seem to be taking just fine. I can see that the phone registers with my Asterisk server but 'sip show peers' reports that the phone

I have a Polycom Soundpoint IP 500 that I have been using with Asterisk for a few weeks. It has been working OK, no major problems other than a freeze up every now and then, until today. The power apparently went out last night and for some reason the phone appears to be working but I keep getting the following errors repeating over and over in my Asterisk log file (IP's X'ed out): Aug