similar to: E&M wink start patch

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

I am preparing to connect an asterisk box with a redfone fonebridge to a T1 service provider. I am doing this by testing first with another asterisk and a Sangoma card playing the role of telco. I formerly had this test configuration operating flawlessly as a PRI connection. But I discovered that I will need to use E&M, thus I've chosen the parameters as described in the subject

Hi List, I have some T1 750s; hookup via a T1 to a TE420P card. We have them all set as E&M wink trunks. We get a dial tone and can call numbers, but when i call another number the ringing I hear on my phone is very weird, its not the standard ring tone. What will cause this? Is this a * setting or something in the Adtran I am fixing, I just want good ole ringing to be heard! Any help would

List: I already have asterisks up and running on a PRI, but where we are moving we cannot get a PRI so we are going to get T1. My question is: We are going to us E&M Wink for signaling with DTMF and caller id. The channels are going to be setup like this, 12 channels for 2-way and 12 channels for incoming only with DIDs. How would I configure the zaptel.conf? I realize that I will have two

Hey folks, I'm pulling my hair out on this situation and would welcome some advice: I'm using the AMI Manager to Originate calls onto 2 E&M wink T1 circuits via a T4XXP card from Digium. Everything works fine for about 600(+/- 50) calls then the Manager is suddenly unable to launch calls. Using ZapBarge to listen to the channels themselves you can hear the dtmf digits being dialed,

Does anyone know the default E&M Wink timings for Nortel DID ports? The default settings on Asterisk are: ; prewink: Pre-wink time (default 50ms) ; preflash: Pre-flash time (default 50ms) ; wink: Wink time (default 150ms) ; flash: Flash time (default 750ms) ; start: Start time (default 1500ms) ; rxwink: Receiver wink time (default 300ms) ;

Anybody ever put a Sangoma and a Digium card in the same server? Specifically a four port card from each company? -bill wlloyd@slap.net

Hi All, I have a rather peculiar problem. Whenever I dial out over ZAP/g0 the phone will just ring and ring, even if I answer the phone on the other end. Whats strange is that the * phone will continue to ring even after I've answered and (sometimes) hung up the dialed phone. If I make an extension to just directly dial out on ZAP/1, its almost the same behavior, it will continue to

I'm getting red alarms with my T100P card that last from 4-15 seconds. They seem to happen randomly, every couple of days. Has anyone seen this behavior, or does anyone have any ideas regarding what would be causing it? Thanks, Glen

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the

I've noticed a problem with calls to Hangup when talking to my Norstars over channelised T-1 E&M trunk lines - it's been present since I started to fiddle with Asterisk last December and it's still present in 'Asterisk CVS-HEAD-08/13/04-10:37:13'. Specifically, when a call is connected to Asterisk from the Norstar DTI card to my T100p I get the following conditions

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system correctly

Hi all, I've got a fairly simple setup, a 4 port zaptel T1 card with 1 PRI and 2 flat e&m T1's coming into it, and its working perfectly except for one small thing. When people dial any of the numbers on either the PRI or the T1 from outside of the pbx, they dont get the "ringing" sound. It just directly connects the call. I know this isnt much, but its started to

I'm a bit confused about how to handle this. I have Asterisk sitting in the middle between a Qwest Long Distance T1 (Voice T1, D4, SF, AMI) and an external voice mail PC using a Dialogic D/240SC-T1 card. The Qwest T1 originally was connected to the Dialogic card directly. The signaling was set to E&M Wink Start because Dialogic used this as its default settings, so it just worked