similar to: Sip registration question

Hello. Sorry to repost this message but, I don't have the original message in my inbox nor in my sent box. Well, last week I posted a problem I am having trying to use an asterisk server use a voip provider and a pstn. Pstn works fine but, I cant even connect to my provider's server. I don't know what I'm doing wrong. I tried using a soft phone and I'm able to register and

Hi, I'm having difficulties with using DUNDi between two servers. If it were three I think I could control looping by limiting TTL, but with two I'm not sure how to prevent a loop causing bad things to happen. I've tried ttl=1 but things still blow up. The DUNDi configurations are pretty simple and work just fine in both directions as long as only one of them is using the switch

Hi guys, I have an Alcatel 4200 with a ISDN board pluged in the asterisk server with TE110P. Input calls VOIP Proider ---> Asterisk ---> Alcatel Output Calls VOIP Proider <--- Asterisk <--- Alcatel In alcatel phones, users should dial 2 for take a line tone and can dial. At this point start my problems: 1. When users dial 2 on phone (alcatel) they don't received a dial tone,

Can someone tell me what I am doing wrong? Why doesn't CDR(duration) or CDR(billsec) return the correct values? cdr.conf endbeforehexten=yes extensions.conf [macro-Dial] ; ${ARG1} - Dial String exten => s,1,Dial(${ARG1},,M(post-dial)) exten => h,1,NoOp(Call was hung up - ${CDR(duration)} seconds long, billed for ${CDR(billsec)} seconds) The log shows: -- Executing [h

Dear All, I am trying to recieve call from inbound proxy then route to internal peer (localhost) and then route to outgoing sip proxy but it failing with subject error. Can any one please correct me what i am doing wrong in below config. SIP.conf [Inbound] type=peer context=introuting host=184.107.XXX.XXX disallow=all allow=all [astinside] type=peer context=introutingB host=localhost

Evening everyone (obviously depends on when you're readin this, but hey). I'm trying to set up a multi * server situation, and am falling over at the second server, and after a day of google etc, have come up against somewhat of a brick wall. I can make calls each way between the two servers no problem, and can include the required extension at the remote * server as part of my main

Hi, I am attempting to make about ten calls simultaneously and intermittently get 'SIP/voipprovider is circuit-busy' followed by 'everyone is busy/congested at this time" I am not sure if this is related to my bandwidth to my voip provider, a configuration issue or something else. Has anyone seen this before and have any suggestions. Thanks in advance. --------------

Hi, i am from Germany, so excuse my School English. I use Asteriks 1.2.12.1, zaptel 1.2.9 and mISDN Rc25 - since my update of Asterisk 2 wooks ago, Echos accure in my SIP Calls. I use SNOM 360, sometimes there is no echo (for example if i call myself via SIP->Asterisk->SIPProvider->TELEKOM->ISDN) but if i call other people there occures Echo many times. The Routing is always the

Hi all, The firmware I used is pa168s_iax2_us_151011.bin. My problem is the handset dial before I finished key in all the numbers, no matter how fast I managed to press the keys. It appeared it always dialed immediately, for example "011862", when I actually ment to dial 0118620xxxxxxxx. Thus left the remaining numbers "0xxxxxxxx" unsent. The handset had its dial plan

Hi list, My Asterisk config for outgoing calls is the following: exten => s,1,Dial(SIP/${MACRO_EXTEN}@voipprovider,60,g) exten => s,n,GotoIf($[\"${ANSWEREDTIME}\" = \"\"]?pri:hang) exten => s,n(pri),NoOp(Problems with voip provider trying PRI) exten => s,n,Dial(Zap/g2/${MACRO_EXTEN},60,g) exten => s,n(hang),HangUp in most cases it works well but, if my

Hi people, I would like to read your suggestions as to where the issue might be. ATA286=Grandstream Budgetone ATA 286 in SIP mode. One Lan Port and one FXS port. TDM04B= 4 FXO signal fxls There is a 8FXO-to-SIP unit in this scenario that works perfectly so i will not make mention of it. PSTN----VOIPprovider---Internet---ATA286------tdm04b---Asterisk1.2.-13 Asterisk is being used as a meetme

Sorry for the duplicate post but I have hit a brick wall trying to get this to work. Is there anyone who can help me? I am having trouble trying to register with a voip provider using sip. I am able to connect using xlite softphone. in xlite i use domain/realm: providerdomain.com sip proxy: host.providerdomain.com:9000 this difference in domain and sip proxy host is whats causing

I'm setting up an alternative submission relay host for dovecot. Atm, it's pointing @ fastmail.com. with dovecot config, submission_relay_host = smtp.fastmail.com submission_relay_port = 465 submission_relay_ssl = smtps submission_relay_ssl_verify = no submission_relay_trusted = yes submission_relay_user = 'acctID at mydomain.com'

Hello. >> ubuntu*CLI> sip show peers >> Name/username Host Dyn Nat ACL Port Status >> voipprovider xxx.xxx.xxx.xxx A 5060 Unmonitored I've ben trying to connect an asterisk server to a voip provider, and I'm currently wondering what the 'A' in the ACL field of the 'sip show peers' command might

TL;DR: It's okay to close a bug, if you can justify it properly. Recently there has been a spate of bug-closing with what I would call inadequate documentation. Comments such as "Obsolete?" or "I assume it's fixed" could be applied to nearly every open bug we have. While this does reduce the open bug count--something I have been watching with morbid fascination

Piling on... InterNIC says the domain was created almost a week ago, and expires in a year. The registrar is GoDaddy. The owner of the site is located in the Dominican Republic: C/1ra #15 Costa Criolla, Km9 Carr. Sanchez Santo Domingo, New York 00000 Dominican Republic Registered through: GoDaddy.com, Inc. (http://www.godaddy.com) Domain Name: CDSPORTAL.NET Created on: 14-Mar-08 Expires on:

Isn't svn set up to auto-parse and post to the bug so you can just say "fixes bug 44444" and it parses it out? I mean, i added that to gcc like 15 years ago, i'm surprised we don't do this :) Nobody should have to add this info manually unless someone forgot to put it in a commit message. On Tue, Jun 12, 2018 at 1:36 PM, Tom Stellard via llvm-dev < llvm-dev at

https://gcc.gnu.org/viewvc/gcc/hooks/ is how it was done. This used the incoming email handling for bugzilla i set up. These days, you could just use bugzilla's rest API IE a simple variant of https://github.com/mozilla/github-bugzilla-pr-linker/blob/master/app/app.py should work as a commit hook. That thing is written as a service, you just need the find/add parts of the rest api, rip

Hi, i am recording a message, but it is always cut off at 40 secs. There are no time out configured. Gabriel -- The educated person is not the person who can answer the questions but the person who can question the answer.

Is it possible to rsync through a firewall that requires HTTP basic authentication? The RSYNC_PROXY variable seems to correctly direct the request to go through the HTTP proxy server on the firewall, but there's no way to specify a username/password combo. The error message reported by rsync is "bad response from proxy - HTTP/1.1 401 Authentication required", which is not