similar to: Multiple ISDN BRI Units with Asterisk using Bristuff zaphfc in NT mode?

-----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Zoltan Szecsei Sent: zaterdag 16 juli 2005 12:54 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Multiple ISDN BRI Units with Asterisk usingBristuff zaphfc in NT mode? >> Maybe this is rather a hardware question,

Hi, Can anyone please point me in a direction as to how to set up these 2 pci cards with AAH 1.1? I have (am still) googling left, right & center - but haven't found a definitive guide yet. The centos based setup lacks any of the tools I know (insmod, modprobe ....) so it is time consuming just to even dig around the AAH box. There are no zaptel.conf files ....and on it goes. A

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

Hi All, Long time no chat ;-) Asterisk 1.0.9 (sometimes) won't authenticate IAX phones after re-boot of SuSE 9.3 box I've traced the problem to be with the firewall and the fact that I have 2 NICs in the box. Now that I have opened port 4569 on both interfaces, asterisk seems happy *but* does anyone know how to force SuSE 9.3 to always bring up a specific NIC before the otherone? On

Hi, all I have couple of SIP phones and they are in [from-sip] context. I also have an IAX2 phone. I have put this one in [iax-user] context. I want to make calls between SIP and IAX2 phones. If I put them all in same context all is fine, however when they are in different contexts they will not call each other and I will get message (in * CLI) that particular extension does not exist in a

Good day all What is the amount of calls that asterisk can handle,SIP and from/to PSTN -- Thanks Altus Snyman Stormcorp Network Solutions +27 11 8071141 exten 301

Caller id is not in the configs that are supplied with zaphfc from bristuff, and it's not mentioned in the wiki. Is it possible to use callerid with zaphfc/bristuff? Thanks!!

I have ISDN BRI line (Point-to-multipoint), with HFC card and bristuff/zaphfc driver. I also have TA attached to NT, with analog phones and modem on it. When I'm dialling through Asterisk/bristuff, and in the same time TA have some conversation (or maybe modem link) on channel 1, I can hear that conversation (or modem) very short period (0.2sec), and I also disturbing that conversation

Hi, We've been using zaphfc single ISDN cards as cheap Zaptel timing sources for our Asterisk boxes for a long time, and in the asterisk 1.0.x series, had zero problems doing so. I now have some boxes with Zaptel 1.2.x (with a mixture of 1.0.x asterisk and 1.2.x asterisk), and this setup no-longer seems stable - By plugging or unplugging the ISDN cable, and sometimes just randomly the card

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

I'm using bristuffed Asterisk with ISDN/ZAPHFC I have VERY ugly (outgoing) sound through ISDN/HFC if echocancel=yes in zapata.conf, but without echocancel I have bad (incoming) echo Through PSTN/FXO sound is ok with or without echocancel. I tried other echo cancellers (in zconfig.h) two times: ECHO_CAN_KB1 (this was default) ECHO_CAN_MARK2 ECHO_CAN_MG2 after any change I compiled (make

Using the latest(?) bristuff (Asterisk 1.0.4-BRIstuffed-0.2.0-RC3a) I have problems with loosing the D-channel. Most of the time, after the message "PRI D-channel down" it only takes a second or so to come back up, noted by the message "PRI D-channel up" However, today most of the time the D-channel stays down. Calls come in, but can't be answered. Does anyone know

I would like to know how to install asterisk 1.0.9 with zaphfc working on a SuSE 9.2. I tried this: - The rpms with SuSE 9.2 are asterisk 1.0.6 - bristuff works, except for zaphfc, which doesn't compile. - The official asterisk download file doesn't contain isdn bri support Any ideas? Lars Dybdahl.

On Friday, March 31, 2006 3:52 PM Chris Earle wrote: > I'm wondering if I should be using zapHFC with my Junghanns card > instead of qozap? Why would you want to do that? Sorry if I missed the start of the problem but qozap is what you want to use with your Junghanns card (at least if you want to stay with zaptel/libpri). > Everyone always mentions zaphfc -- mostly I >

> Appreciate the replies everyone -- really > > I'm wondering if I should be using zapHFC with my Junghanns card instead > of > qozap? Everyone always mentions zaphfc -- mostly I guessed because they > are > using a zaphfc-compatible card ----- but *maybe* I should try that instead > of qozap??? > > And yep -- totally know about the module load order thing and

Hi, Is it possible to both use Digium B410P and bristuff'ed 1.4 Asterisk, now ? I've heard BRI support in Asterisk is about to change with 1.6 but I'm not sure I understood what the plan is. If someone has a clue, l would delighted to learn about it. Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Since the X100P/X101P/Clone cards does not work in all countries that use DTMF based Caller-ID systems, I've developed a hardware that you connect to a serial port and the PSTN. You then run a perl script "cid_logger.pl" as a daemon, and modify extensions.conf to call an agi script whenever a call comes in, and if it's on the X100 card it will get the caller id information

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Does anyone test Asterisk 1.2.X + bristuff-0.3.X and TDM card? We can't get it to work. -David -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Julian J. M. Sent: Friday, March 31, 2006 1:44 AM To: Chris Earle; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Re: BRI

Hi, I have following problems compiling bristuff-0.2.0RC8m. Has anybody seen them before and can point me in the right direction? zaphfc/make all: ---------------------- /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c: In function 'hfc_findCards': /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c:1000: error: invalid lvalue in assignment make[2]: *** [