Displaying 20 results from an estimated 8000 matches similar to: "TDMoE and callerID"
2007 Dec 02
1
T1 Timing Troubleshooting
I'm having (I think) timing issues in relation to bridged T1-T1 calls via dynamic spans. Fax calls are intermittently working, but voice is fine. My box has a Sangoma A400 inside it as the primary Zaptel timing source. My T1 PRIs that are hooked to the box come in via a foneBRIDGE2 (dynamic TDMoE spans). PRI #1 is the telco and PRI #2 is an existing Comdial FX-II. For some reason, bridged TDM
2003 Oct 23
1
Number of TDMoE Channels?
I was trying to establish a TDMoE span of 4 channels between two Asterisk
servers. Machine A has a T100P to our PBX. Machine B has no Zaptel
hardware. With 4 channels (e&m signalling) the red alarm never clears, and
eventually machine A panics. With 24 channels, the TDMoE span seems to work
perfectly. Is this hardcoded somewhere? I don't really need a full 1.544
Mbps between my two
2006 Jan 24
3
ZAP - Can't pickup calls on Analog Trunk
We have 4 analog line and 2 analog trunks. On the trunks we have all
the DIDs coming into the current phone system. Trying to get everything
moved over to Asterisk but having issues picking up the calls on the
analog trunk.
We can receive calls on the plain analog lines and we can call out on
all analog lines and analog trunks. When a call comes in on the trunk
line the ZAP channels don't
2005 Jun 22
4
FXS interfaces
Hi all,
Does somebody know why no load modules to FXS? I used zaptel-1.0.7
version driver.
[root@server1 zaptel-1.0.7]# modprobe wctdm
ZT_CHANCONFIG failed on channel 3: Invalid argument (22)
Did you forget that FXS interfaces are configured with FXO signalling
and that FXO interfaces use FXS signalling?
/lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed
2003 Apr 23
2
Tor2 with em_w (or em) signalling pickup behavior?
Hi,
Can I make e&m wink start lines just wait for digits - instead of going to
default?
Someone else cleared a similar problem (as described below) on an fxo port
with "usecallerid => no" but it is not doing the trick for me. In this case
the line when straight to default which would be ok also.
John
I posted the stuff below about a week ago...
I set up a t1 from my sys75 to
2006 Jan 13
2
zapata.conf for non pri T1?
Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance
T1), our current pbx has the signaling set to E&M, I can set em in
zapata.conf, but I'm trying to track down the proper entries for the
zaptel.conf file. The digium docs only show a PRI example. Our current
system has these settings:
Signalling: E&M
Framing mode: ESF
Line Coding: B8SZ
here's my
2004 Jul 16
3
Echo problem update - POSSIBLE SOLUTION
After speaking with several people, and even participating in a forum of
several other people with echo issues, I thought I'd share what we've
done (well actually what our chief R&D engineer, Brett Bourn has
done...)
First let me say that normal cheapy PC hardware couldn't be made to
function with out echo. We tried on both the single port Digium T1 card
and the 4 port Digium T1
2008 Jan 02
5
Missing "zap" command in Asterisk 1.4.16
Hi list,
I've just compiled and installed Asterisk 1.4.16 and when I try to run "zap
show" I get the message "*No such command 'zap show'*".
I have a Sangoma Remora A400D with 2 FXS / 10 FXO ports, I've installed the
latest wanpipe too.
zaptel-1.4.7.1 was compiled from the wanpipe installation, so I don't know
what's happening here!!!
Any ideas???
2004 Nov 21
3
TDM400 FXO stops handling outgoing calls, but still accepts incoming?
I have a bit of a weird problem that I'm having great trouble debugging.
I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules
are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID,
which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS.
Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls.
My
2003 Nov 20
4
T1 / Channel Bank Configuration
I know this topic has been covered before - I just want to make sure I
am understanding this correctly.
| -------------------
| | |
| T1 | Channel Bank |
| ----------| |
| | T1 Cross | |
| | | |
| | -------------------
--------------
| Asterisk |
| |
|
2009 May 20
1
Channels configuration with DAHDI
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi all!
Days ago I bought a OpenVox A400P card with a port FXS and another FXO
that I am testing with my Asterisk installation in my house. I'm using
Asterisk 1.4.24.1 with DAHDI Linux 2.1.0.4 and DAHDI Tools 2.1.0.2 on
Debian GNU/Linux Lenny.
I was reading "The future of telephony" and this [1] document looking
for information about
2007 May 15
4
Outside lines are just not happening...
Two problems, possibly related:
Here's the configuration...my Asterisk box has a TDM844B in it; port 1-4
are FXS, 5-8 FXOs.
Here are the config files:
/etc/zaptel.conf:
--------
fxoks=1
fxoks=2
fxoks=3
fxoks=4
fxsks=5
fxsks=6
fxsks=7
fxsks=8
loadzone = us
defaultzone = us
--------
/etc/asterisk/zapata.conf:
--------
[channels]
language=en
usecallerid=yes
hidecallerid=no
2004 May 04
2
Can Asterisk support R2 signaling
Hi All:
I'm a newbee to Asterisk. I currently working on a project and want to know
if Asterisk does support R2 Signaling.
Thanks
Begra8fl
>From: asterisk-users-request@lists.digium.com
>Reply-To: asterisk-users@lists.digium.com
>To: asterisk-users@lists.digium.com
>Subject: Asterisk-Users digest, Vol 1 #3647 - 9 msgs
>Date: Tue, 04 May 2004 13:32:00 -0500
>
>Send
2003 Oct 14
2
T100P to Adtran TA750 - No dialtone or ring
Hello all,
I've got a T100P connected to an Adtran TA750 with a T1 crossover...
This connects to a patch panel with phone ports. The Adtran is fully
populated with FXS cards.
All I get on any phone port is a fast clicking noise... No dialtone.
Asterisk 'sees' the card, (the channels show up in /proc/zaptel).
Incoming calls are routed to the zap/x channel, but no ring.
I'm
2005 Feb 18
1
Help with config.
Hello all.
I am trying to get my second x100p card set up and am having some troubles.
My zaptel.conf reads:
fxsks=1-2
fxoks=3-4
defaultzone=us
loadzone=us
before adding this card my zaptel.conf read:
fxsks=1
fxoks=2-3
defaultzone=us
loadzone=us
But now that I've made the change I am getting the following error when
running modprobe wcfxo and of course the same
2007 Nov 20
1
FXO Hangs up automatically
Hi,
I'm having problems using a TDM400P Card. I put my SIM card in a Nokia
Premicell and connected it to a TDM400P card but when I make calls to
the number, it hangs up automatically. The card also can't call out.
Any ideas? I've searched the archives without much success. I
appreciate all your help.
Details:
I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an
2011 Apr 02
1
Problem getting TDM400P clone card to go off-hook and dial
I am having problems getting a Nicherons TDM400P wildcard clone to dial out.
Everything appears to be configured correctly, but although I see call
progress, it never seems to actually pick up the phone.
(The following is a test of 911 emergency, where I substitute 811 [repair
service] as the actual number dialed.)
*CLI>
-- Executing [911 at from-internal:1]
2004 Sep 11
2
TDMoE questions
Hello,
I want to link several * boxes together. Some of them are dedicated as
"user" servers (SIP and IAX clients connect to them) and some are used
as PRI servers (where the PRIs are hooked onto).
I think TDMoE is the only channel type where you can group different
Interfaces into a single group.
E.g. for using Dial(ZAP/g1/12345), I think you cannot group different
IAX accounts
2003 Sep 13
1
ZT_CHANCONFIG failed on channel 1: Invalid argument (22)
no matter which way I have my /etc/zaptel.cfg
this only started happening after a yesterdays CVS update
to my zaptel source...
Line 1: fxoks=1
Line 2: fxsks=2
Line 23: loadzone=us
Line 28: defaultzone=us
<End of File>
Zaptel Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
2 channels
2004 Jan 08
1
latest cvs == broken tdmoe
Hello,
I've been using TDMoE accross 2 * boxes for months. It was working well,
but * would crash when anyone would try to connect via h.323. So, I got
the latest CVS release and compiled without h.323 support. After I made
and installed the latest CVS the TDMoE channels stopped working.
They have been working great (especially after we got echo cancel working
them, thanks Mark) and the