similar to: beronet and tdm400p cards conflict?

Hi, I'm using Asterisk 1.2.1 on a Debian Sarge with a TDM400P and a monoBRI using chan-mISDN from beronet site. It seems to work all right except for autodial calls, monoBRI ISDN channel behaves differently waiting for the caller to answer and then continue. Asterisk console says: analog: -- Attempting call on Zap/2/3391818250 for 104@inbound_originate:1 (Retry 1) > Channel

Hi. I'm trying to get a Beronet QuadBRI card work with bristuff drivers. Though qozap module loads right, all card spans are in deactivated status. I'm quite sure my configuration is correct and using a single BRI card instead of the quadBRI the status is active and I can place and receive calls. On Beronet installation manual I read that Beronet and Junghanns cards are identical in

Hi, I've just installed a beronet BNS40 on Asterisk 1.2.9.1. Everything seems ok, asterisk gives no error (nothing inside logs) but the 4 led on the back of the card (which is NOT connected to an ISDN line) are red and flashing....what does it mean? Is it not properly working or it means the card is not connected to any ISDN line? The card handbook says the card has red led but not their

Hi, I have an Asterisk 1.2.9.1 box connected to an ISDN line via a beronet card (with ports in PTP mode). I noticed a long delay when making outbound calls, more precisely between (taken from Asterisk CLI) "Called 1/XXXXXXXXX/s" and "mISDN/1-u43 is proceeding passing it to SIP/8-5486" I searched on misdn.org but found nothing. I'd like to understand if this delay is

Ciao, I have an Asterisk 1.2.9.1 box with a beronet dualBRI (install-misdn-queue) on a Debian distro. I'm experiencing problem with some Telecom Italia lines: some people cannot choose menu selections or extensions after hearing intro message. Is there anybody who knows if there is a particular parameter to set inside misdn.conf (or maybe some other configuration files) ? TIA Giorgio

... Activating "sip debug" shows the register packets but nothing in return. ... I think that this is a network related issue, but you have to solve it by using a Asterisk config file. Unfortunately I think that the faster way to solve your problem is trying to understand if sip messages are correctly sent to tnet. I strongly suggest to use http://www.wireshark.org/ previoulsly named

tnet.itand SIP register messages are not replied. I suggested to check if your Asterisk box is really sending SIP messages, you can use a net sniffer. Did you alerady used different sip client with the same sip account of your Asterisk box? Did you use zoiper from the same box? Marino p.s. Are you Italian? On Mon, Jul 14, 2008 at 5:27 PM, Giorgio Incantalupo < gincantalupo at

We're using an SC420 and using BRI with a quadbri Junganns card, with IAX softphones and one hardphone. Working well except that we sometimes get dropped connections between IAX and the server with a max retries exceed message, which comes from the chan_iax driver code. The BRI side of things looks like it is fine. I had been thinking it might be a network issue but now wonder if it is an

Hi all, has anybody ever encountered this ERROR before? It happens frequently on my debian6-based pbx. I'm using Asterisk 1.8.11 with dahdi-linux-2.4.1 and a quadBRI card. ERROR: chan_dahdi.c: PRI Span: 3 PROBLEM: General: Badly Structured Component I tried to google but without success. Do you know what it means? Should I worry? Thank You Giorgio

Hi, I'm installing an Asterisk box with a TDM2400P in Brazil. I can make analog phones work while lines are not working. Since I do not know anything about brazilian lines, is there anybody who can tell me what is wrong/missing in my conf files (below)? TIA Giorgio _zaptel.conf:_ fxoks=9-16 fxsks=17-24 defaultzone=br loadzone=br* * _zapata.conf:_ context = inbound_zap echocancel = 128

Hi, I am trying to use zaptel module on an Ubuntu 5.10 distro (2.6.x kernel) using gcc 4.0.2. Compilation does not give me errors so after a 'make install' I try to load zaptel module with insmod but the following error arise: *insmod: error inserting '/lib/modules/2.6.12/misc/zaptel.ko': -1 Invalid module format* Is there anybody who can help me?? TIA Giorgio --

Hi, does anybody know what *zttranscode *module* *is for*?* Thanks!! Giorgio -- _________________________________________________ Giorgio Incantalupo, mailto:gincantalupo@fgasoftware.com FG&A srl - http://www.fgasoftware.com - Voice@Work - The Agile PBX http://www.voiceatwork.eu Tel: 02997663.14, Fax: 0291390172

Hi, I'm using a HFC card on my asterisk box. I tried to make a conference but it doesn't work. I read on internet to use ztdummy but my server has no uhci (only ohci but it doesn't work) so I cannot use it. I tried zaprtc but after loading the module (it appears when typing lsmod) nothing has changed. Should I buy a x100p to get the right timing? Or there is another solution? TIA

Hi all, since Asterisk 1.4 seems to have too many differences from previous versions, wouldn't be nice to have a new mailing list? Giorgio Incantalupo

This is a function of the Phone itself. Asterisk has nothing to do with it as it does not know anything about the call until after the SIP device 'sends' it. To my knowledge it is not posible. I don't even think a SIP standard is available for this. This 'feature' along with changing CallerID Display after a call has been answered is something missing from the RFC. >

Hi, I'd like to build a personal PBX connecting 4 or 5 analogic phones with a ADSL line and I'd like to know what is the right card I need I visited digium site and I think TDM400 could be the right choice but I cannot understand how it works...I think it has 4 slots where 4 modules (FXS or FXO) can be inserted. How many cards do I need to connect my ADSL line to 5 phones? I think I

Hi, we have an asterisk 1.2.1 box and 2 polycom SIP phones. We'd like to show the called name on the calling polycom display instead of his /her extensions as I do with the caller name on the called polycom. Is it possible? If yes, how? TIA Giorgio Incantalupo

Hi, I guess I'd need to run Beronet quad and octo bri cards under bristuff to get zaptel features (echo canceling, timing source).... Am I right or could I achieve this also with chan_misdn - their native driver ? Running bristuff on Beronet cards is unsupported. Has anyone succesfully run Beronet quad BRI cards under bristuff recently ? Do they work ? Regards, Rob.

Hi, is there anybody who knows what this warning means?? WARNING[27309]: chan_sip.c:8875 reload_config: Section '10' lacks type TIA Giorgio -- ____________________________________________________________________ GIORGIO INCANTALUPO Tel. +39 02 9350 4780 (104) FG&A Software 20017 Rho - Via Puccini, 8 E-Mail : gincantalupo@fgasoftware.com Internet: http://www.fgasoftware.com

pbx18*CLI> module load codec_g729-ast14-gcc4-glibc-pentium3.so Unable to load module codec_g729-ast14-gcc4-glibc-pentium3.so Command 'module load codec_g729-ast14-gcc4-glibc-pentium3.so ' failed. [Dec 22 15:52:45] WARNING[4491]: loader.c:757 inspect_module: Module 'codec_g729-ast14-gcc4-glibc-pentium3.so' does not provide a license key. [Dec 22 15:52:45] WARNING[4491]: