similar to: Dialogic D/300 E1

I found an old Dialogic card in an abandoned PC, that I think is a Dialogic D/41EPCI based on some googling.. The lspci output says: 00:09.0 Bridge: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01) Subsystem: Dialogic Corp: Unknown device 0529 I'm just getting started with Asterisk to build a SOHO system. Any suggestions for what I can do with this card? It would be

I'm trying to connect an Asterisk T1 port to a Dialogic card. The Dialogic side is an external VMS. I setup for ISDN-PRI between systems and have green lights on both card/ports. Zttool shows connection is good also. However, when I try attempt terminate or originate a call to either system, nothing appears of CLI. How can I monitor the "D" channel? zaptel.conf: # Span 8:

Is there ant chance of the Dialogic card model D/4PCI working with asterisk ? Best Regards Steve Beaumont

Hello, I just wanted to know if any of you has successfully (or know about) installed the Dialogic 4xFXs ISA CARD D/41 ESC? Does it work with *?, if so, how is the driver called? Thanks a lot for your comments. Alejandro Acosta,-

We have (10) Dialogic D/240SC-T1 REV 2 voice boards. Prefer single buyer, take all (10) for $675/ea Cory Andrews ***************** b2 Technologies 454 Sonwill Drive Buffalo, NY 14225 ***************** voice: 866-44-B2TECH X22 fax: 716.630.1548 email: sales@b2llc.com

Steven Critchfield <critch@basesys.com> wrote: __________ >On Wed, 2004-05-26 at 14:23, tpanton@attglobal.net wrote: >> On which subject, has anyone else >> got time to work with me on a chan_dialogicGC ? It looks do-able but I am ignorant of how asterisk does threading. > >Do you have GPL drivers for the dialogic card? Follow previous comments >about licensing.

Darren, yes, I'd be happy to help. I'll contact you off list to sort out the arrangements. I should warn you that it may be a wasted journey for you, as I really dont know if it will exhibit the problem. Tim. "Storer, Darren" <starusers@comgate.tv> wrote: __________ >Hi Tim, > >TP> So it _may_ not be a problem for me as NTL is a patchwork >TP> of

1. D/120JCT-LS card with 12 ports. This ports are FXS ports? 2. It is true that "Dialogic drivers cost of $15 per channel" ? 3. Can I use this hardware with asterisk (for E1-ISDN using Wildcard E400P <http://www.digium.com/index.php?menu=wildcard_e400p>) ? 4. Anyone with experiance can tell me how they work and can provide a configuration example? (2 DSP Motorola procesors - I

Hi All, I've had a great success these last couple of days on bringing up Asterisk with a load of Cisco 7940 phones and a couple of soft phones as well. I'd really like to try and link this in to my companies PBX so I can call in from the PSTN as well. I understand there is a charge for the module that would allow me to use my old Dialogic board, can anyway provide some more information

Can someone share pointers to Asterisk's Dialogic support? Which boards are supported, driver status, and etc. Thnx

Speaking as former Dialogic/Bayonne user who was frustrated for months with Dialogic's complexity and months of initial testing with GlobalCall only to use their many-years-old and very complex base Dialogic drivers(and eventually scrapping it all for Digium/Asterisk and being up one week later), I can tell you that Digium/Asterisk is definately the way to go. It is 1000 times easier to

Hi Mark We setup a small IPPBX using Asterisk. So far we've been using it for voip network. It's been working fine. We also have a Dialogic D/4PCI four port FXO board with us. We've found some references in the user guide available on your web site and couple of other mailing transaction threads that Asterisk provides pay-for-add-on support for Dialogic h/w. Can you please tell us

Hello all, I found a LSI161SCREV2 Dialogic board in one of my drawers, and i was wondering if by any luck, i could make some magic happen with asterisk ... If asterisk does not support it, is there any PSTN to H323 or PSTN to SIP gateway that support this dialogic card and that can be connected to an Asterisk Box? Digium, I PROMISE that I will buy my cardf rom you once my tests are conclusive

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Spanish/Espa?ol: Hola a Tod at s, Estoy en la implementaci?n de una soluci?n a medida en la cual requerimos conectarnos v?a SIP a un IMG de DIalogic y salir hacia otras centrales (MSC) v?a SS7, la conexi?n entre Asterisk y el IMG es SIP, pero como requerimiento necesito enviar un NOA (Nature of Address) con valor 8 por requerimientos normativos, hasta ahora no he podido encontrar como puedo

Hi, Asterisk 1.4.17 Sangoma a102DE I'm having some issues sending CallerID Name to a Dialogic based phone app. According to the pri debug (asterisk2a-pri-debug.txt in [3]) you can see that it is sending the CallerID Name "Mike - Budgetone - reachme.com" to the Dialogic card, but it isn't regestering on the Dialogic based system. I can receive CallerID Names from our Paetec,

I acquired a board identified as a Dialogic/4 for which I've not been able to locate any technical details. Can anyone identify this board or point me to some technical data? Thanks. -- Regards, Scott Dudley

Hi- I've been considering writing some self-test software for several quad-E1 cards that I've just received from Digium. I don't have an E-1 channel bank, so this would be my way of checking that everything hardware-wise is working fine before I head out to the dark and cold confines of my customer's equipment room - to make everything work with their E1's. I was thinking of

Please rest assure that I have been following the * development for a while and understand the value the Digium hardware gives me vs any other vendor. Most of the people on this list probably know whats good for everyone else, but I like to find out for myself (I am not a CNN junky). Now the * site mentions Dialogic as supported hardware at: http://www.asterisk.org/index.php?menu=hardware It