similar to: TDM01B card configuration

Simple question that google hasn't helped much with (likely poor search terms) I just installed a Sangoma A200 with overall good results. Initial tests with both incoming and outgoing calls were very positive. Until I made a normal call that lasted more than 30 seconds. I setup the FXO with kewlstart signalling, and the outgoing call is never registered as 'Answered' and the dial

I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel bank (12fxs/12fxo). I have the setup partially working thanks to some help from IRC. However I still have the following issues I can't seem to resolve 1. When calling into the system from the PSTN call hangup is not detected. * leaves line in use until it is shutdown. 2. When calling an analog phone connected to

*** Now you just need a "phone" or "station" (FXS) device and a method of connecting it. *** So... essentially I need to spend another $125 US on a Wildcard TDM400P so I can plug in an analog phone? On the X100P description it says: "The X100P supports FXS Loopstart and "Kewlstart" (Loopstart with far end disconnection supervision). It can detect ringing and

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

so i have been running v1-0 on all of my test boxes for about a month now testing iax/sip/res_xxx. I decided to put it into production so I updated a box that was running 0.9.? that had been working perfectly for months and low and behold the inbound line from telco now intermittantly doesn't clear and none of the other channels can dial out on that line. I have tested the line in this

Is anyone on the list using an Audiocodes gateway with asterisk and SIP? I'm looking at that platform, but I have a couple of issues: 1) Echo cancellation. The echo that I'm hearing with an X100P is unacceptable. Does the Audiocodes do better? 2) Line signalling. I'm using Kewlstart with the X100P, but it looks like the audiocodes uses loopstart only. How does this work with

Hi.. I've got an asterisk setup with an X100P card installed.. I'm noticing that upon hangup, it takes a good 3 to 5 seconds before asterisk realizes the line has been hung up and drops the call.. this causes my SIP phone to continue ringing, and occassional phantom voice mail messages to be left.. I'm located in good old standard North America, with a regular Verizon residential

Hi All, I recently purchased the Asterisk Developer's Kit (TDM) to try out Asterisk. After following the directions in the Digium's FAQ topic entitled "Q. How do I configure my TDM40B and X100P?", I'm receiving the following error: WARNING[1074428608]: File chan_zap.c, Line 6748 (load_module): Ignoring rxwink ERROR[1074428608]: File chan_zap.c, Line 6692 (load_module):

Hi All, I've got an MD3200 modem which is working as a Zaptel FXO interface for Asterisk (X100P clone I believe). It seems to work, but on incoming or outgoing calls I can hear the other party ok but when I speak, I hear my voice echo back at me (quite quietly but it's distracting!) on everything I say. The other party doesn't seem to hear the echo - they just say I sound a bit quiet.

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

Hi everyone, I've just got my X100P card installed and working but there seems to be an issue with hang-up supervision. If I stuff a call out over the X100P card onto the PSTN that's fine. When I hang up the SIP phone the PSTN call ends. If I receive a call from the PSTN, it's answered and everything is ok until the remote party hangs up. Asterisk thinks the call is still active and

Hi there! I'm setting up a connection between Asterisk ver. 1.2.13 and a Harris 20-20 PBX. More less everything went fine, but the problem I have now is when dialing to the Harris PBX, it seems to pick up my call as soon as it reaches it. For example if from the Asterisk outgoing folder I dial an extension, say 100, and play a prompt as soon as it is picked up, the promt is beign played as

Details: Asterisk 1.0.9 Zaptel 1.0 Dell P3 1ghz with X100P Clone Location: India This is an interesting issue where when I open up ZTMonitor, it shows the RX as being on. It seems that Zaptel doesn't know to hang up the line so after a couple of hours when the telecom cuts the line, everythign stops working. Things I've tried include playing with the zaptel.conf, trying zaptel v1.2(with

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hi, Updating zaptel gives me this during the make. Any ideas, the searches and Wiki gives me no hints. In file included from /usr/src/linux-2.4/include/linux/fs.h:19, from /usr/src/linux-2.4/include/linux/capability.h:17, from /usr/src/linux-2.4/include/linux/binfmts.h:5, from /usr/src/linux-2.4/include/linux/sched.h:9, from

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf