similar to: No BUSY on PRI

I am wanting to front-end a legacy PBX with an asterisk box. I have done plenty of asterisk work over the last 6 months to PRI circuits, but not with a PBX being involved. I know I can use asterisk and digium cards in this manner, but do I need separate cards for the PRI -> Asterisk side to the Asterisk -> PBX side, or will a 4-port PRI card do the job? (I already have a spare one of

hi, well, most of the things work right now due to the help of peter svensson, but after heavy use of our ericsson BP250 today several problems appeared. i split into several mails as they are seperate problems. * i can't signal Busy to the calling party. asterisk receives busy from the ericsson PBX but does not forward this to the external caller. i tried with exten =>

If you see a wj0011 version of firmware for Zyxel Prestige 2000W floating around (I found it in a German forum), KEEP AWAY. It completely trashed the wireless networking in my phone. -- ========================================== Rod Bacon Empowered Communications Ground Floor, 102 York St. South Melbourne Victoria, Australia. 3205 Phone: +613 99401600 Fax: +613 99401650 FWD: 512237

P.S. I _had_ read the other posts that suggest changing to unicast sntp mode. This didn't help. I eventually setup a new ntp server on my LAN, and used it as a sync source. Everything seems OK now. Obviously a problem with my other ntp server. Cheers. -------- Original Message -------- Subject: Cisco 7940 - Disappearing Clock Date: Thu, 28 Jul 2005 11:50:35 +1000 From: Rod Bacon

We have just had an ISDN PRI service commissioned here in AU (using Powertel as provider). I have called them and ensured that we have the ability to set Caller ID on our service to any number in our 100 number block, and I have been assured that everything is OK from their end (unlikely). Every time I drop a sample.call in to /var/spool/asterisk/outgoing with the Callerid: option set, the

I was wondering if anyone had experienced the following with asterisk stable. After a period of time (can vary), If I stop asterisk and try to run ztcfg -v to reinitialise my quad e1 card, the server will lock up. Sometimes it's a complete lockup, where it won't even return pings, other times it seems to be "partially screwed". -- ==========================================

I have 2 servers, configured identically. Each has a TE405P and 2 PRIs. One server was experiencing crackly audio on one circuit, accompanied by HDLC bad FCS messages. The telco recabled and moved me to another port on the DMS-100. The audio is better, but there are still bad FCS problems on the span. I have moved the PRI in question to the other server, and the problem does indeed move with the

Hello, i have succesfullu setup asterisk with Sangoma E1 card, evrything works well but i don't know how to pass indications from telco switch to the user - when users call bad number telco switch shuld talk "unallocated number" but its only send PRI_CAUSE 1. How to pass voice indications thru asterisk to clients? My /etc/zaptel.conf: span=1,0,0,CCS,HDB3,CRC4 dchan=16

I switched PRI vendors recently, and one of my questions was "do you provide caller ID name in addition to number?" AT&T Local did not, But XO communications said they did. Before I call to complain, is there an setting to turn this on in asterisk? I want to make sure that I have my side covered before I call XO. My current zaptel.conf is: context=from-pstn switchtype=national

I posted something on this a week ago, at which time I was told that this was an 'old' issue. Since then, I've spent hours looking, but can't find the answer. For some reason, some of my CDRs (both to CSV and MySQL) are being written with the wrong callerid. As best as I can determine, they are being written with the CLID of the _last_ caller to access the specific ZAP channel

I've posted this to SNOM, but was wondering wheter anyone here has issues with SNOM 190 phones not showing the correct DST adjusted time (using the latest firmware). -- ========================================== Rod Bacon Empowered Communications Ground Floor, 102 York St. South Melbourne Victoria, Australia. 3205 Phone: +613 99401600 ? ?Fax: +613 99401650 FWD: 512237 ? ? ? ? ? ? ? ? ?

Hi, I've an PRI coming to my asterisk ,calls are coming fine and my agents are able to answer no prob. but I've an agreement with my telco with some incoming no if the no of calls on these no are more then 3 then send to another no. they use busy signal to divert call on another number so I'm sending the call to Congestion() if no of calls in this group are more then 3. But my

Hello, On a Asterisk 1.6.1 powered system, I've just discovered that using Busy() application in dialplan was no enough to send a Busy signal on incoming Dahdi channel. On this specific install, adding an Answer()) and a Playtone() statement in dialplan triggered sending of busy tone but I'm still surprised by my findings. Should I expect public switch to send a Busy tone to caller

When I dial a PSTN (via * with Digium Quad-E1) number, I hear two sumultaneous ring tones. One is coming from *, the other I assume is from the ATA. Is there an intelligent way to get around this?

I have googled until blie in the face, WiKi'd until physically exhausted and searched through every Asterisk repository that I can find, all to no avail... No matter which version of SpanDSP I use, with which version of libtiff, Asterisk, ... I simply cannot send faxes. I can receive faxes *perfectly* (sending from standard fax macine on POTS) into tiff file (via Digium analogue card),

Nobody has been able to answer this. Not even Digium at this stage, but I'm hoping someone here, smarter than I, will be able to. We are running some TE406P (upgraded 405Ps) cards performing mainly PRI bridged calls. After a server is brought up, calls sound absolutely perfect. Over time, delay (latency) creeps into the calls. What is really weird about that is apparently with the new

Can someone who is knowledgable in the traditional telco space please give me a layman's explanation (or point me to an appropriate url) of LBO as per the zaptel configuration file? # The line build-out (or LBO) is an integer, from the following table: # 0: 0 db (CSU) / 0-133 feet (DSX-1) # 1: 133-266 feet (DSX-1) # 2: 266-399 feet (DSX-1) # 3: 399-533 feet (DSX-1) # 4: 533-655 feet (DSX-1)

I'm new to H.323 and I have noticed that there are two separate channel drivers for * available - the inbuilt one, and oh-323. I had trouble compiling oh-323 with the current cvs stable, so I tried the inbiult one (with specifiec recommended versions of openh323 and pwlib). It compiled cleanly but I am told that it is not recommended (unstable?). Can someone with first-hand * H.323

Hello, I just got off the phone with my PRI provider, and was told that I am not sending an expected message when I reject a call with a Cause Code for Unassigned(1) and Congestion (42). Busy works fine though... Anyhow, they are seeing the RELEASE COMPLETE message with cause code 1, however the tech told me they expect a PROGRESS indicator with a value between 1 and 10. Any ideas on how

I'm having trouble setting the outbound caller ID on calls I make from my PRI trunk group. The PRIs are served out of a 5ESS. Telco has set the PRIs up for user provided caller id information, so I believe I just don't have it set up right in my dialplan or something. I can't seem to find an example of setting the outbound caller ID specifically for a 5ESS. Does anyone have an