similar to: Error on incoming calls

Hi Kape, Life is generally good with bristuff and the quadBRI cards. However I've got a concern: how does one return a busy signal to the telco when all B channels are busy? Right now, when all channels are in use, the remote caller is kept waiting until the telco times out and finally get a busy signal (on a land line) or error tone (mobile). On the asterisk side here is the output: --

Hi, I'm getting unusable DTMF detection with DISA on incoming ZAP channel (bristuffed *) on quadbri from GSM gateway. DTMF detection works ok in normal ISDN incoming line. How can I check what's going on ? What settings to check ? Anyone with more experience on such scenarios ? Thanks in advance, regards, Rob.

hi gang! I'm interested in setting up incoming PPP on a system at work that has a fresh (not upgrade) Centos 4.4 on it. All the documentation I've found for that shows using mgetty to do it, and seems pretty straightforward. However, that machine doesn't have a binary named mgetty anywhere. It does have a mgetty-sendfax RPM installed, but it does not provide a binary named mgetty.

Just reading up on DMARC, toying with setting it up to auth against incoming emails. (but not configure my domain to use dmarc, or at least not yet) ran into an article about opendmarc, which is available on epel. but when I took a look at the opendmarc website and the git pages it doesn't appear to have been updated in several years. while I see that it is still available from epel, I

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hi there, I just upgraded a relatively old Asterisk installation (1.2) in our office to a relatively new version (1.6svn from last wednesday) which runs a Junghans QuadBRI card [1]. To get this flying I got dahdi-linux, dahdi-tools and libpri from SVN as well. After a while of juggling it "works". What doesn't work: connected ISDN devices (Gigaset phones connected to QuadBRI

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

Hello, I am trying to install the drivers for the Junghanns quadBRI card, but am having a problem. I have essentially followed the procedure from http://www.voip-manager.net/installation-linux-asterisk.php. At the stage to install the ISDN card I have completed the following: 1) downloaded the bristuff-0.2.0-RC8q.tar.gz to /usr/src 2) unpacked it in /usr/src - tar xvzf bristuff-0.2.0-RC8q.tar.gz

Hi, I'll soon replace a Junghanns OctoBRI with a Junghanns QuadBRI. As both use wcb4xxp driver (dahdi 2.3.0, libpri 1.4.10.2 and asterisk 1.6.1), I'm planning to proceed this way : 1. Edit 2 versions of files /etc/dahdi/system.conf and /etc/asterisk/dahdi-channels.conf (one for each card). 2. Link current system.conf and dahdi-channels.conf to QuadBRI files. 3. Power PC off 4. Swap cards

Hello, I have bought a targeta quadbri. I want to realize a PBX server to send and to receive fax on lines BRI. I have installed asterisk and the drivers of quadbri (bristuff_0.2.0-RC7b). I downloaded and installed the module spandsp-0.0.2pre10 When i send a fax from the fax machine to asterisk, the application rx_fax saves the fax in a file on the hard disk. The problem comes when I try to send a

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hi All, I am unable to 'net rpc vampire' the NT4 user accounts and groups into an ldapsam. The PDC is Windows NT4.0 sp6a and the ldapserver is SunONE DS 5.1 on Solaris 9. I believe the sambaSamAccount schema has been imported successfully (output below). Any help received is greatly appreciated. Thanks. Darren. Here is what happens... [root@mitosis bin]$./net rpc join -S NT4-PDC -w

Below is the topic list for the latest digest form of the mailing list. See if you can pick out the real messages from the myriad of warnings. :-( Today's Topics: 1. Autoreply to Thank you! (helpdesk@cdfreaks.com) 2. Symantec AVF detected an unrepairable virus in a message you sent (Administrator@fai.ie) 3. Re: Runaway SMBD process (Gerald (Jerry) Carter) 4. Re: Your

I got the same problem, and what i change it was point-to-point to point-to-multi-point, and I used normal patch cable to connect the ISDN card to ISDN connector, and I used TE mode. In italy work like that I hope that will help you, I used also bristuff. Good luck ________________________________ Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]

Hi, I have an asterisk box with a QuadBRI. I am close to make it work like I want: Incoming calls to SIP are OK, outgoing calls are quiet working thanks to Michael Sandee advices. My real problem is that my * box is freezing very often when I probe qozap (bri-stuff 0.0.2). I have tried two distribs (Debian Kernel 2.6, Mandrake 9.1 Kernel 2.4) and it always work for a few minutes and freezes. At

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out: