similar to: Re: Asterisk-Users Digest, Vol 11, Issue 77

Hello All i have big problem for unicall. my system work successful with sangoma card, E1 and CAS signalling (vietnam). when at the some time. i have trouble then my system is half (CPU instructions = 100) i tested for some case as belows: - When i dial, then my system became answer, the caller hangup. system error message show (loop without condition and half machine) Jun 11 12:15:45

Hi When I make a call from the outside to asterisk and the call is asnwered, all is OK, but when I make a call from the outside to asterisk and hangup before the call is answered, you got this WARNING in the console: Jul 6 19:33:08 WARNING[10037]: channel.c:1521 ast_read: Exception flag set on 'UniCall/2-1', but no exception handler Jul 6 19:33:08 WARNING[10037]: channel.c:1521

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line

Dial(UniCall/g1|300|) Where is the number you want to reach? I'd expect to see Dial(Unicall/g1/1234567890|300) To reach number 1234567890 - Mois=E9s Silva On Jan 30, 2008 1:21 PM, Roger C. Beraldi Martins <rogerberaldi at gmail.com> wrote: > Dears, > > After weeks trying to contact support of my telecom about 'Seize Ack' > because that is not returned, was a

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hi all, I still haven't seen my first post (cry for help) so I'm not sure if these are going through or not ... I've played with the box all day today ... I got it to quit seg faulting finally by playing with the config files. Currently I have 4 spans configured for a Digium TE420B (With Octastic DSP) Here is my zaptel.conf: (I know the device connected to spans 1-3 are providing

Hello All. I'm using sangoma card A-101. tested successful with E10 (ACATEL) Exchange, connection with E1, CAS, (using unicall-0.0.3pre4). my system run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

I've been trying to configure an E1 in Mexico using unicall, i went into vozdigital, googled this list, and finally followed this instructions: http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2 I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10 "channels" assigned from my telco. However when i try to simulate a call using this call file: --------call

Hello All I'm using asterisk 1.1.X and MFCR2 lib version 0.03pre2. when i call to E1 (connected with asterisk), chan_unicall don't detected event incoming call and show error. error messages: *CLI> Warning, flexibel rate not heavily tested! Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 4 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

I followed the how-to for R2 that coppice wrote on the webpage http://www.opencall.org/installing-mfcr2.html, now asterisk has channel unicall and when i test an incoming call I get the following errors. astbox:~/mediatel/libmfcr2-0.0.1# asterisk -r Asterisk 1.0.0, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com>

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia (north africa). I have configure my MFCR2 according argentina R2 settigs : the test call run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2. generally in the begging no errors occur. after

Hi everybody We are having periodically troubles with the outbounds calls, seem like the PBX cannot end to dial the entire string of numbers This is output from the PBX., few minutes after all work fine again ... :(, and few minutes after the same problem appears. Thanks in advanced ... Regards This is the PBX aout and my zaptel, zapata confs. Runing asterisk 1.0.9 libmfcr2-0.0.2

Hi. I am in the Brazil. I have a problem on Unicall for Asterisk 1.4. I am working with E1 with 30 channels. Message when it receives calls: chan_unicall.c:2603 handle_uc_event:unicall/1 protocol error.cause 32772. My files: /etc/zaptel.conf: span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 loadzone = br defaultzone = br fxoks = 32-55 /etc/asterisk/unicall.conf: [Channels] language=br

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]

---------- Forwarded message ---------- From: Juan Carlos Huerta <juancarloshuerta at gmail.com> Date: 07-abr-2009 13:41 Subject: Re: [asterisk-r2] MFCR2 With Unicall - can unicall affect zaptel commands? To: asterisk-r2 at lists.digium.com Please wirte to asterisk-users at lists.digium.com to get help about this problem. Juan Carlos ~ Lo que no te mata te fortalece ~ On Tue, Apr 7,

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but