similar to: Does Debian Bristuffed Asterisk work ignore Beronet cards ?

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

Hi, a few month ago, I tried to install zaptel for my Beronet BN8S0 pci card... I gave up and took hfcmulti/lcr. Now dahdi (2.2.1.1) seems to support the card and I'm very interested to get it to work. But how to get rid of these annoying qozap driver? bishop dahdi # lspci -v -nn -s 01:00.0 01:00.0 ISDN controller [0204]: Cologne Chip Designs GmbH ISDN network Controller [HFC-8S]

Hi there, I am attempting to set up a simple BRI and SIP based platform using * with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and zapata.conf files. For the inital test I'm simply trying to connect to the * demo menu. The drivers compile (with a few warning that I believe aren't important - see attachments). chan_zap comiles with the warning: chan_zap.c:

Hello list, After upgrading from BRIstuff 1y-b to 1y-e my ISDN card is suddently detected as 2 ports instead of 4. I still load the driver as "modprobe qozap ports=12" as I've always done. But now it only sees 2 ports. Output of "lspci -vvv" ------ cut -------- 02:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem:

Hi, In my 1.6.1.18 with dahdi 2.2.1.1, I've got : # dahdi_hardware pci:0000:01:0a.0 qozap- 1397:16b8 Junghanns OctoBRI ISDN card Does it mean I should download and use qozap or is it a bug in Dahdi ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100412/de87e46e/attachment.htm

Hi all, I'm trying to get a junghanns QuadBRI to coexist in the same machine as a Digium TDM400P card (so I can run the ISDN lines in and bridge with analog phones plugged into the TDM). I'm having a problem loading the modules. If I follow the BRIstuff (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod qozap.o I'm on Debian 2.4.31. That works. But then I

Hi. I'm trying to get a Beronet QuadBRI card work with bristuff drivers. Though qozap module loads right, all card spans are in deactivated status. I'm quite sure my configuration is correct and using a single BRI card instead of the quadBRI the status is active and I can place and receive calls. On Beronet installation manual I read that Beronet and Junghanns cards are identical in

Hi, Using Xorcom's bristuff-0.4.0-RC4-xr7.tar.gz (ie asterisk 1.4.25) with an old Junghanns OctoBRI (ie not the 2.0 version), zttool shows every port in TE mode, though half of them are in NT. Alarm column shows OK for every port, such as : OK octoBRI PCI ISDN Card 1 Span 1 [TE] Lay Globally, this system doesn't work (can't dial out through zaptel) Replacing this board

Hi, I'm pulling my hair down and getting bold :-) ..... I have Asterisk between Panasonic KXTD816 and Euroisdn in Italy (beronet octobri and bristuff Asterisk).... I'm trying to do just plain transfer of call from pbx to ISDN through Asterisk... It seems like PBX hangsup, when call is progressing with no apparent reason. I'd kindly ask for any advice or some working example for

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hello, I am trying to install the drivers for the Junghanns quadBRI card, but am having a problem. I have essentially followed the procedure from http://www.voip-manager.net/installation-linux-asterisk.php. At the stage to install the ISDN card I have completed the following: 1) downloaded the bristuff-0.2.0-RC8q.tar.gz to /usr/src 2) unpacked it in /usr/src - tar xvzf bristuff-0.2.0-RC8q.tar.gz

I may have found a source of an A-Ticked HFC 4BRI PCI adapter in Australia, and will be testing one next week if all goes well. I don't want to post the details of the reseller online unless invited to do so, so if nobody replies and says they are interested then I won't :) I'll follow up once I've tested it. Let me know if you want the details. James

Hi, (cc. asterisk-users, hope that is not a big Faux Pas) I've had trouble with the qozap driver for a LONG time now, where it will not recognise and ignore a missing ISDN2 line on a quad card if one of the 4 ports is unplugged or somehow faulty. The symptom is that is correctly recognises the fault, but then clears the RED ALARM almost immediately, leaving Asterisk thinking that it can call

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o

Hi, When typing dahdi_scan on an OctoBRI-enabled setup, I've got only 8 replies such as : [1] active=yes alarms=RED ... [8] active=yes ... framing=CCS I would expect 16 replies (one per B-channel). Is this correct ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All I have a Junghanns BRI 4 port installed where only the first channel of each line is working i.e. channels 1 and 4 work but 2 and 5 don't. Our config is the same on this box as 15 other similar installations where all works well. the only error I see is in /var/log/messages: Jun 28 15:49:31 pbxct kernel: qozap: CRC error for HDLC frame on card 1 (cardID 0) S/T port 2 Jun 28 15:51:27

hello, Here (http://updates.xorcom.com/astribank/bristuff/1.4/INSTALL.html) you can read : cd qozap modprobe zaptel insmod qozap.o (for kernel 2.4) insmod qozap.ko (for kernel 2.6) ztcfg I thought modprobe was a replacement for insmod. Can someone be kind enough to explain : 1. the difference between modprobe and insmod, 2. why should both commands be issued, 3. how modprobe and insmod compare

Good day all Is there a fix for these errors yet for the junghanns cards Jul 26 17:15:05 pbx1 kernel: qozap: dropped audio card 1 cardid 0 bytes 6 z1 1 z2 107 Jul 26 17:15:18 pbx1 kernel: qozap: dropped audio card 1 cardid 0 bytes 6 z1 10 z2 116 Jul 26 17:15:18 pbx1 kernel: qozap: dropped audio card 1 cardid 0 bytes 5 z1 118 z2 97 Jul 26 17:16:33 pbx1 kernel: qozap: dropped audio card 1 cardid