similar to: Cannot receive incoming calls via ISDN

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

Hi, We've exhausted our internal capabilities as well as Sangoma tech support and were hoping someone with some expertise could help us with a pointer. Briefly, our issue is as follows. Periodically (several times an hour), we get either of the following error messages in our asterisk messages log. These correspond with dropped outbound calls on a one-to-one basis when the second error

I have a dial plan that includes a company phone directory as a main menu option. If they just sit at the main menu, after 20 seconds, they are transferred to the operator. If the user picks an extension from the directory, they are transferred to the proper extension. If the called number is not available, they are transferred into VoiceMailMain. They leave a message, and hang up. The hang

Hello. I have been beating my head over this problem for about 6 hours now. I have a SIP peer, who I register to (successfully), who should be directing all incoming calls at my [default] stanza in my extensions.conf: [ Context 'default' created by 'pbx_config' ] 's' => 1. Wait(1) [pbx_config] 2.

Yes, I have tried that too (i.e, exten => +17775551212,1,Log(WARNING, TWILIO)). It does not work and NO error message in CLI. I have also tried http://orourketech.com/elastix-plus-sign-caller-id-messing-things/ since I first emailed this group, but that does not seem to work either. Here is my log: [Dec 2 15:09:28] NOTICE[26464]: res_pjsip_session.c:1920 new_invite: Call from

Hi Folks, I've Asterisk Bristuffed up and running behind an Auerswald Commander Basic ISDN PBX on the internal ISDN Bus (BRI/PTMP). The HFC Card works marvelleous for outgoing calls (as the parallely installed avm fritzcard with chan_capi does), but when I'm trying to call in, I get a short ring signal and then the connection is terminated. This does not happen with chan_capi and

Hi, I have the SuSe9.2 installed in a box with a QuadBri. I have followed all the instructions i have found and this is my best result... only one error compiling zaptel :( .. y have the kernel sources an already made the links to its drwxr-xr-x 8 root root 328 Jun 16 20:20 . drwxr-xr-x 12 root root 320 Jun 16 14:05 .. drwxr-xr-x 3 root root 136 Jun 16 20:17 asterisk drwxr-xr-x 22 root

Hello Group I have a Asterisk server running with 2 Digium T1 cards installed. 1 card connects to Telco via a PRI. The 2nd card is connected to a fax server via Digi DataFire RAS 24 PT1 Adapter (Digi0001). The idea is to have Asterisk route the calls based on DID or FAX tones. Everything is working great so far. The only problem is the Fax server does not see the DID. How can I tell if Asterisk

bri-stuff.0.1.0-RC4a on debian sid with 2.6.7 kernel isdn sk: Bus 0, device 18, function 0: Network controller: Digi International Datafire Micro V (Europe) (rev 2). IRQ 17. Master Capable. Latency=16. Max Lat=16. I/O at 0xe400 [0xe407]. Non-prefetchable 32 bit memory at 0xd8021000 [0xd80210ff]. i still receive error messages continuosly (every few seconds) i

Hi, I've been playing round with Asterisk on Redhat 9 (2.4 Kernel) and was experiencing bad echo problems using Budgetone 100's when calling analogue lines in uk (Isdn4Linux / Digi Datafire). Calls to other ISDN and mobile network seemed ok although not much testing done. I've tried installing Asterisk on a faster processor (P4 3.0 GHZ) with a 2.6.8-24 kernel to see if that helps.

Greetings to everyone! I am new to Asterisk and ISDN modules so i tried to follow many of the articles about capi, bristuff, mISDN and so on. Now I am working in mISDN but every way I try I have compiling errors! The HFC PCI card is a Digi Datafire Micro V. The bristuff give me the error "invalid module format zaphfc.ko" and I don't know how to compile and load it. The capi

I am running asterisk 1.0.1 with OH323 compiled in. We have a 323 trunk to CallManager with a mgcp controlled pri router. When using sip phones (directly registered with asterisk) to call out the 323 trunnk to PSTN, calls timeout after 3 rings. If I answer b4 3 rings - no problem, otherwise I get "no one is available to answer at this time" on the consoel and it redirects to an

I upgraded to 0.7.1 from a cvs version from a few weeks before 0.7.1 was relesed. now I am having troubles with my dialing plan and voice mail. As part of the upgrade I re-built the machine so there was a blank slate however after installing 0.7.1 I had no mail box creation script and could not figure out how to go about creating a mailbox, any suggestions would be usefull. I have looked at

So, incoming calls on zap work just as I expect them - an intro is played, the caller hits 1 for sale 2 for support or dials an extension. I'm using the privacy option for all extensions. When calls come in from zap, they caller is played the priv-recordintro recording, they say their name, and everything happens normally from there on out. However, when the call comes in from sip and

Hello All, I was wondering where does Asterisk stores the blacklist numbers? I looked into the dialplan and it shows that it *"Set(DB(blacklist/${blacknr})=1)"* the number... Does it save in MySQL DB? hyperion*CLI> show dialplan app-blacklist-add [ Context 'app-blacklist-add' created by 'pbx_config' ] '1' => 1.

Hi Everyone, After a fair amount of faffing ive managed to get the 2000w working with asterisk for IP -> PSTN calls (i.e. get the phone to make and receive calls over our BT line). The final solution is to set up outgoing VoIP calls but I now know that without a SIP aware router I can think again! (damn you iptables!) In the mean time I'm trying to figure out why I can't get the

Hello everyone... I'm trying to get up a testing pbx installation. Following instructions of what've read from the handbook and from asterisk's wiki, I wrote the dial plan as follows: [general] ; ; static = yes ;[globals] ; [default] ; exten => 0,1,Answer() exten => 0,2,Playback(fcopba1) exten => 0,3,Hangup() exten => *0,1,Answer() exten => *0,2,Record(fcopba1:gsm)

When I first to the "add extension" the "show dialplan" has the lines that say "SIP/" but after I do a "save dialplan" and a "stop gracfully" and restart the lines with "SIP/" are gone. ************************ "Show dialplan" before: ************************ asterisk01*CLI> [ Context 'default' created by

Hi, How does * read and process the extension.conf file?? The reason I ask is that I think it probably has a very large impact on how the calls are routed and processed by the system especially when it comes to least cost routing.. Let me explain...with an example.. I am using the * Devkit to get to grips with the system, so I have and X100P (Zap/1) and and S100U (Zap/2).. Below is my

I have an "outbound-ld" context as follows: [ Context 'outbound-ld' created by 'pbx_config' ] '_1NXXNXXXXXX' => 1. Macro(enumdial|${EXTEN}) [pbx_config] 102. Wait(1) [pbx_config] 103. Set(LINE=${IF($[${LINE}=pots]?link2voip:${LINE})}) [pbx_config]