similar to: 5000 sip clients (voip phones)

Does anyone know if the E1 cards that digium sells work in India. Also are there any distributers for those cards in India. By E1 cards I mean E100P, TE410P or TE405P -- regards Vikram (http://www.vicramresearch.com)

Why is SER considered a better SIPserver than asterisk , why is it that SER can handle more clients than asterisk can. And if this is just cause of say poor SIP handling code in asterisk then is there anything being done to fix it. Just wanted to know why SER claims to be better than asterisk as a SIP server. ? -- regards Vikram (http://www.vicramresearch.com)

I have 20+ asterisk servers and need to network them together so a phone on any of the servers can call a phone on any other server without any trouble. I can think of IAX trunks between every server. So every server will have an IAX trunk to every server and then prefix bases routing in the dialplan for each server (I can give a number to each server and use that as a prefix for that server).

I am planning to go in for a E1 line and whould like to know what questions i need to ask my service provider so i can connect that E1 to my asterisk box using the digium E1 card. what I mean is will my service provider give me info like LBO, framing , coding etc which i need to configure the span tag in the zaptel.conf and what about B and D channels am I allowed to setup whichever channel I

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS

I configured agi-test.agi on extension 111 when i dial into asterisk extension 111 using a IAX softphone and hangup while the AGI is playing asterisk crashes. Does anyone have any idea why this happens. -- regards Vikram (http://www.vicramresearch.com)

After days of searching i've finally figured out that E1 lines in india use multiple types of signalling from EuroISDN to R2. Digium E1 cards dont work for R2 type signalling. Can anyone suggest me asterisk compatible E1 cards which would work on R2. Also if anyone on this list is from INDIA and uses asterisk and E1 lines please let me know what type of cards (which vendor) do you use and what

I just came across libr2 anyone using it in its current state. Specifically someone from India or around India using it. Also does it work with the digium e1 cards or only the Dialogic cards. http://digium-cvs.netmonks.ca/viewcvs.cgi/libr2/ -- regards Vikram (http://www.vicramresearch.com)

Hello, I have setup mongrel successfully a few times now, but, each time I have used apaceh 2.2 and mod_proxy setup descibed on the mongrel site. However, I need to set up another app in a subdomain. example.com/docserver instead of docserver.example.com. I have tried just adding I have something like: ProxyPass /docserver/ http://example.com:3001/ ProxyPassReverse /docserver/

I set up a bios update option on a PXE server, when it boots and starts to run the exe for the bios I get the error: Can not run from protected enviornment. Can any one help me reconcile this issue so I can get the bios update .img to work correctly. Thanks for any help guys. Thank You BP Computer Consultants Bryan Pershall (MCSE, Dell Certified) IT Consultant ------ Office: 281-469-6456 Cell:

Hello, new to the group. We have been using PXELINUX for some time now with great success. However, with the recent spawn of virtual machines now supporting PXE boot, has anyone been able to mount the disk in this enviornment? Could someone direct me to any information on how to mount and or partition drives? I have discovered the same issue with the HP DX2200 model of PC. For example if I run

Hello all, I came across a behavior of R with environments that I'm not sure what is causing it. It involves changing variables that are found through using model.frame on a formula inside a function. I wonder if it's a "bug" or a "feature". And in either case, how it might be managed. Here is a simple example: # let's say we have an x and y variables: temp_x

Hello, I''m trying to figure out how to setup a spec structure for plugins. I''m getting pretty lost in figuring out how to isolate a plugin enviornment emulating rails, but not actually being reflected upon the current rails project. What I mean is this, let''s say I have a comment plugin. This has two things in lib, the comment model (comment.rb) and then the module

On Thu, Apr 20, 2017 at 11:00 AM, Scott Neugroschl <scott_n at xypro.com> wrote: > > On Wed, Apr 19, 2017 at 1:02 PM, navern <livingdeadzerg at yandex.ru> wrote: > >> Is there any available tool with this for pre-evaluating the resulting sshd_config for fatal errors? I'm not demanding: I'm thinking "that could be really, really useful". > >

Below is a crash I get on my gentoo box when I execute the set command in wcmd. I believe the problem is caused by wine using the entire enviornment from my linux machine: john@jmd0 ~ $ wcmd WCMD Version 0.17 W:\home\john>set ALLUSERPROFILE=c:\windows\Profiles\Administrator ALLUSERSPROFILE=c:\windows\Profiles\Administrator ANT_HOME=/usr/share/ant-core CLASSPATH=. COLORTERM=

Hi, I am having problems getting winbind on a BDC to work in a Samba3 /LDAP Enviornment and have one straightforward question. Should the secrets.tdb file on the BDC contain an entry with the name of the BDC , e.g. where BACKUP is the name of the BDC ?. { key = "SECRETS/SID/BACKUP" data =

Hi, I have a R script with a funcion in it. When I run this script under R enviornment, it works fine. But if I go to DOS command prompt and type "rterm --slave < foo.r" it says: Error: couldn't find function "myFun" Execution halted Below is part of my code. Does anyone know why? Thanks, Yu-Ling Wu ================================================

0 down vote favorite I notice that in my production enviornment (where I have memcached implemented) in see a cache-control - max-age header in firebug, anytime I am looking at an index page (posts for example). Cache-Control max-age=315360000 In my dev environment that header looks like following. Cache-Contro private, max-age=0, must-revalidate As far as I know I have not done anything

Greetings! When compiling R-1.5.0 on Solaris 5.8, I got the following error message (see below). I've been using R-1.4.0 with no difficulties. I renamed the previous R installation to R-1.4.0 (following suggestions of an earlier post by Peter Dalgaard) before compiling R-1.5.0. And I've checked that the enviornment variable R_LIBS is not set. Is there something I overlooked? Any

This coming out of WWDC. Pretty cool to see this kind of thing happen. -- J "Brien" | HybridIndie Productions | http://hybridindie.com | hybridindie@gmail.com -------------- next part -------------- An HTML attachment was scrubbed... URL: http://wrath.rubyonrails.org/pipermail/rails/attachments/20060807/380ae29c/attachment.html