similar to: H323 setup problem

During debugging of H323 trunk side (using Jeremy Macnamara's H323 driver in ~/channels/h323) a couple of things come don't quite work as advertised... 1/ the following line in extensions.conf explicitly sets the outgoing caller ID (required in my case for downstream GK processing..) exten => _1NX.,1,SetCallerID,6400047602100 exten => _1NX.,2,Dial,H323/${EXTEN:1} what

hello all, i want to have ooh323 connection between asterisk and cisco. in my scenario, asterisk is gateway and cisco is gatekeeper. this is my ooh323.conf file: [general] port=1720 bindaddr=192.168.0.227 gateway=yes faststart=yes h245tunneling=yes h323id=gw10 at test.com settracelevel=10 gatekeeper=192.168.0.212 context=from-trunk disallow=all allow=ulaw allow=alaw allow=gsm dtmfmode=rfc2833

Greetings- As most of you who monitor this list know, I've been messing about with Asterisk -HEAD, Cisco Callmanager, and the nufone H323 channel driver here for some time- with pretty decent success. I'm hoping to cash in a chip here- I've run into something that is probably a very simple answer, yet not found a decent reference to resolve it. Scenario- -HEAD as of last week

Hello All Anybody had used ooH323 for asterisk i using ooH323-0.7.2 and asterisk CVS may 2005. OpenH323 1.17.1 and pwlib 1.9.0 and GNUGK 2.0.2 audio is very good, better than SIP and IAX, but i have problem. how to router call from openh323 to outside PSTN. my h323.conf setting ; Objective System's H323 Configuration example for tvcti ; ooh323c driver configuration ; ; [general]

Hi, I am trying to communicate H323 and SIP users. I have configured h323.conf, sip.conf and ooh323.conf. If I am using gatekeeper (gnugk) then I am able to call successfully to h323 users using SJphone. And same for SIP users also. But when I disabled gatekeeper and trying to call using gateway with sjphone then every time whatever number I dial the call goes to asterisk and some computerized

I have tried everything. to register with this gatekeeper to make and receive calls These are the details I received from the voip provider: protocol H.323 Gatekeeper Address - AVS@210.21.118.XXX Port - 1719 RAS - 53 Q931 - 80 h245 - 1722 RTP - 1722 Username - H323 I have 2 phone number/accounts with this gatekeeper that I need to register to. ID - HMA0200.10szxn-xxxx e.164 - 22xx2912

Hello, I'm trying to register with a gatekeeper using chan_h323, I have a Login, Password and a user (telephone) number, This is my h323.conf [general] port=1720 bindaddr=x.x.x.x (my fixed IP) gatekeeper=x.x.x.x (gk ip) allowgkrouted=yes allow=all [xx] (my login) type=h323 e164=111 (my assigned phone number) secret=1111 (my password) context=incoming I'm getting this error when trying

Dear All. I have installed Asterisk-1.0.6 on FreeBSD-5.4 RELEASE via port, so the chan_h323.so modules already included. When i try the SIP channel, asterisk works fine. In this case, i use the XLite softphone as client, i can hear the voice transfered through clearly. Asterisk is good!! :D The problem is when i try the H323 channel, the voice cannot be transferred through. I have

OOH323 Debugging Enabled -- Executing Answer("SIP/3513-090f7d40", "") in new stack -- Executing Wait("SIP/3513-090f7d40", "1") in new stack -- Executing DeadAGI("SIP/3513-090f7d40", "a2billing.php|1") in new stack -- Launched AGI Script /var/lib/asterisk/agi-bin/a2billing.php a2billing.php|1: line:58 - IDCONFIG : 1

All, I'm haveing a bit of trouble getting my head around H.323 and call routing with Gatekeepers, Zones and intra-zone calls - hopefully someone who is more informed in things H.323 will be able to point me in the right direction...? I already have a mature network of Asterisk boxes dotted around the UK and overseas with hundreds of extensions and our own number-plan/dial-plan in the form

Hello group, I am trying to register to a opengk h323 gatekeeper using chan_h323. The gatekeeper expects me to register a username like 31201234567@gatekeper.com with a password secret and an e164 of 31201234567. Thus I put the following in the config file: [general] gatekeeper=w.x.y.z. AllowGKRouted=yes [31201234567@gatekeer.com.com] type=h323 e164=31201234567 secret=geheim

Hi, I'm trying to configure Asterisk as SIP-H.323 Gateway via ooh323, but I have an error relatively to the GK Confirmation message. >From the log: "H323 RAS channel creation - succesful Sent GRQ message Gatekeeper Confirmed (GCF) message received ERROR:No Gatekeeper ID present in received GKconfirmed message Ignoring message and will retransmit GRQ after timeout Error: Failed to

I'm trying to configure Chan_H323 to register with GnuGK... without success... i've failed finding sample configurations. I'd greatly appreciate anyone who can provide sample config of H323.conf and gnugk.ini I am tyring to configure Asterisk as a neighbor in GnuGK. I'm always getting this error on Asterisk. ERROR[16384]: chan_h323.c:1987 load_module: Gatekeeper registration

Hello, Thank you for the job well-done. I installed the chan_h323 of the asterisk-1.2.7.1 and with lib pwlib-v1_10_0-src-tar.gz and openh323-v1_18_0-src-tar.gz and I used licensed g729 from digium. However, I am having a very funny behavour. 1. If I send a call on its ringing at the called side but the caller didn't get the ringing tone. 2. if the called picks up the phone, I am

Hello, I'm trying to use the GSM codec with Nufone H323 but it's not working. Does somebody has some idea? Have I missed something? Thanks!! Celso Fassoni Some additional info: (I'm using CVS-HEAD - downloaded today) monkey:~# cat /etc/asterisk/h323.conf [general] port = 1720 bindaddr = 192.168.0.100 ; this SHALL contain a single, valid IP address for this machine

hello all, i want to have ooh323 connection between asterisk and cisco. in my scenario, asterisk is gateway and cisco is gatekeeper. this is my ooh323.conf file: [general] port=1720 bindaddr=192.168.0.227 gateway=yes faststart=yes h245tunneling=yes h323id=gw10 at test.com settracelevel=10 gatekeeper=192.168.0.212 context=from-trunk disallow=all allow=ulaw allow=alaw allow=gsm dtmfmode=rfc2833

For the benefit of everyone, having H323 Configuration problem due to H245 Tunnel, check the h323 Config embeded at the end. Comment the offending line as under: ; ; Enable H.245 tunnelling (yes,no). ; h245Tunnelling=yes ; -----Original Message----- From: Tola Ogunsan [mailto:tolaniye@hotmail.com] Sent: Wednesday, May 25, 2005 1:03 PM To: Kanuri, Seshu (Company IT) Subject: RE: oh323 problems

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

Dear Mailinglist-User currently we`re working with an IP-PBX, based on Asterisk, with SIP, H.323 and ISDN-Capabilities. SIP and ISDN works fine, but H.323 not. In our first test, we started to connect Asterisk to an Cisco IOS-Gatekeeper with the "chan_oh323" (version 0.6.5). We successfully tested in/egress calls without any problems. But when we started to connect our Asterisk

Hi List, I would like create a H323 trunk from Avaya IPOFFICE to Asterisk, but i would like activate a "direct media path" for the RTP transit directly between the phone and the Asterisk. Now, - H323 Trunk is OK - RTP from the phone transit directly to Asterisk (activate "strictrtp=no" in rtp.conf, and "Allow Direct Media Path" option in Avaya Ipoffice) H323: Phone