similar to: Possible to send Calling Number as TON: international ?

Hi all, We need to get better echo cancellation on an Asterisk gateway. Currently it has two TE410P (1st gen) cards. So would it be possible to just buy two VPM450M cards ? Or do we need to buy two new TE412P cards ? In that case a Sangoma A108d card would be nice as well ? What configuration gives the best audio quality ? Thanks, Leon de Rooij leon at scarlet-internet.nl

Only a warning, and doesn't seem to do anything bad. But I can't seem to figure out what these warnings mean? -- Requested transfer capability: 0x00 - SPEECH [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: k [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: o [Feb 17

I have connected asterisk 1.0.7 with Avaya Definity via E1 with a TE100P Digium Card. Inbound calls are working perfectly and I dont have any problem. But when I try to make an outgoing call with my softphone (xlite) I am getting the following messages. Hungup 'Zap/13-1' Executing Dial("SIP/IZ-bc0a", "Zap/g1/3118") in new stack Called g1/3118 Channel 0/1, span 1 got

Hello all, the scenario: Carrier ----S2M------ * -----S2M------Siemens | | SIP Clients and many other features With much help from the list, the PRI links are without alarms and inbound calls are working fine (from both: Carrier and Siemens). But I am not able to dial wether outbound nor to the Siemens PBX. I allways get the message: == Everyone is busy

Hi. recently I have been trying to setup a PRI on asterisk. Inbound calls are working just fine but I am not able to make outbound calls. Does anyone know what I need to change to make outbound calls work? Right now the PRI is instantly hanging up on the outbound calls. I have included full debug info as well as config files. /etc/zaptel.conf span=1,1,1,esf,b8zs bchan=1-23 dchan=24

Dear All, I am trying to setup an ISDN line from local telco on a digium card. The problem I am facing is that I am not getting any caller id from the telco. They say that they have enabled caller id. Please help me out. My zapata.conf -------------------------------------------------------------------------------------------------------------------- [trunkgroups] [channels]

I have a PRI link up and running between Asterisk and a Nortel Norstar MICS v4.1 . I'm having a problem getting the textual Caller Name across the link from Ast to Ns, however numeric Caller ID arrives and displays fine. From Ns to Ast both elements come through fine. I'm forcing dummy values for testing using: exten => s,1,SetCIDName(Test) exten => s,2,SetCallerID(1234561234)

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

Hi, ? I'm trying to figure out what the issue is splicing Asterisk between our Telewest PRI and a GDK-186 with a PRI card. ? We're using the Digium TE405P ? Our telco provider is Telewest, and Telco directly into switch is fine. ? When I splice Asterisk in, I can make and receive calls from Asterisk extensions, I can make outbound calls from the GDK, but inbound calls do not seem to pass

I have attached my PRI debug out put when making an international call - hopefully it can shed some light on the situation. I am sorry if this attachment gets to the list twice, I sent one early this morning, but it has yet to appear - i may have sent that one in error. Kind Regards: Gabriel -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

Hi all, I have several queues defined in Asterisk, but when I put a user in two queues, the user (can) get two calls at once. (One from each queue). Right now, I configured some phones to only accept one call at once, but that has the side-effect, that also direct calls won't come through. Is there some configuration option to make sure that if a user has an open call from a queue, that

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

When receiving multiple calling numbers via a PRI for a call setup, I cannot find the ability to select between either first or last. Is there a way to do this currently? If not, can anyone help me in getting this to work? Here is the dump of the PRI in intensive debugging. Please note that I want the first calling number, not the last. Any help would be much appreciated. Below the PRI trace

Hi, I have a problem with dialling internationals numbers, and I don't now what is the cause. I have one asterisk with a e100p card connected to the Telco (spain/telefonica) and it can dial local and national numbers without problems but when I try to dial a international number it hangs-up. I call the Telco to ask if the E1 can do international calls and it said that it can. I have tried

Hi all, We're trying to hook up our Asterisk config (Card: TE410P) with a Siemens EWSD switch. The link is ok on both ends (green), with no errors. The problem is when we try to make a call from our side (via call files), we get the pri/E1 error Ext: 1 Cause: Temporary failure (41), class = Network Congestion (2) Our Telecom partner (they checked with Siemens) mentioned that we need to

Hello, I have an Asterisk system in the UK using ISDN service from BT. My problem is that the called number is always passed to the provider with the Type Of Number declared as ?national? despite pridialplan (and prilocaldialplan) is set to ?unknown?. My questions are: - How can I find out what the effective value is for the above two variables without actually making a call? (I have very

Hi list! What exactly is the meaning / function of the pridialplan & prilocaldialplan? I've been trying to find out what the different possibilities for these settings are but couldn't find a clear answer. The possible parameters I could find are are : local,unknown,dynamic,national,international and maybe there are more? Thanks!

After setting the pridialplan=unknown I seeing the Called Number TON change to Unknown Number Type but not the Calling Number TON. Should both be following this parameter or not. If not is their another option to change the Calling Number TON? > Progress Indicator (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: User (0) > Ext: 1 Progress

Hi I have recently upgraded my Asterisk system (from 1.2 to 1.4) and I have started to notice the following messages when I recieve a call on my Zap channel :- [Mar 11 09:20:17] WARNING[4294]: chan_zap.c:8851 zt_pri_error: 1 copying 5 bytes LLC I have a single PRI ISDN 30 link to a Siemens Realitis DX. Here is my zapata.conf :- [channels] echocancel=no echocancelwhenbridged=no rxgain=-5.0