similar to: CLI and DNIS presented to Analog extension

Good Day list, Need assistance determining the best place to read up on whether Asterisk can help me out. I have a situation where I need to do the following <PRI from Telco> ------- <Analog Channel Bank>------------<Proprietary Box> | | | | | | <PRI Port 1 of Digium Quad T1> <PRI Port 2 of Digium Quad T1> | | | | | |

Situation: 8 POTS lines, 3 companies, 1 system. Channel banking the POTS lines onto a T1 thru an ADIT 600. The only way our carrier will provide DNIS is thru Analog DID #'s. Anyone know of a piece of hardware that can add DNIS digits to a particular line? -Darren

On 18.08.23 07:39, Darren Tucker wrote: > On Fri, 18 Aug 2023 at 15:25, Stuart Longland VK4MSL <me at vk4msl.com> wrote: > [...] >> The crux of this is that we cannot assume the local IPv4 address is >> unique, since it's not (and in many cases, not even static). > > If the IP address is not significant, you can tell ssh to not record > them ("CheckHostIP

The subject pretty much says it all. Does Asterisk support DNIS, and if so, what kind of connection is required? (T1, PRI) I've got a wink start T1. I've read comments that say the DNIS will be seen as an extension, but I'm seeing each digit of the DNIS as a separate extension. So in my case I send DNIS of 12345, Asterisk will jump from extension 1 to extension 2 to extension 3 to

Hi i have an asterisk pbx with E1 port connected to another PBX. Im trying to send the DNID/DNIS to the PBX here's my dialplan exten => 8881111111,1,Dial(ZAP/g2) exten => 8881111111,n,Hangup() The PBX just get the number 2 as it's DNIS when i change it to ZAP/1 or ZAP/g1 the PBX get the number 1. What should i add to send the extension number as DNID/DNIS? Thanks! --------------

I installed a Sangoma card with the default install. I'm getting five digits of DNIS with each call. The T1 is setup ESF/B8ZS wink start. Each of the digits of the DNIS are being used for extensions in the context. I need a single extension that let me start an AGI script that can use the dnis. Can anyone point me in the right direction to do this? Thanks, David Ruggles CCNA MCSE (NT) CNA

Can someone in Asterisk'land subscribing to 800 service explain to me how to setup extension.conf to route calls based on the incoming DNIS/ANI. For example I want to route 3 incoming 800# coming across a trunk group to all land in the same queue. So I guess I am asking how to perform DNIS/ANI based call routing? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Is there a reason the variable ${DNIS} does not get set with incoming calls via chan_capi ? Is it related to the MSN=X in capi.conf ? version = chan_capi-cm-0.6.3 example; exten => _95555555XX,1,NoOp, ${EXTEN}, ${DNIS} == ISDN1: Incoming call '0400000000' -> '95555555' -- Executing SetCDRUserField("CAPI/ISDN1/955555 55-135", "Incoming") in new

does anyone know how to route a call coming in with ANI*DNIS* Oct 31 12:47:41 VERBOSE[30056] logger.c: -- Executing Set("Zap/49-1", "DID=1231234*4812*") in new stack I tried making a route for _.*4812* but that matched everything rather then just the dnis i wanted.. any ideas? I would preferably like pass the callerid along to my extensions, but for now the important

Hello, Being totally fed up with the lack of quality and reliability from both VoicePulse and BroadVoice, We are switching to a direct IP connection to Global Crossing. We've installed a local point-to-point T1 into their CO, and they will give/take SIP g729a directly and act as the gateway for us. In setting up the inbound SIP service, they are asking the question, "In what format do

I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hi, Is it to possible to route incomming call using dnis information to specific extension or section in the extensions.conf ?? like my users dial my asterisk box using different toll free numbers, but i can't offer them unique services. Plz suggest that if it is possible ? if possible then any example ... Regards Apna --------------------------------- Do you Yahoo!? The New Yahoo!

On Tue, 2003-12-23 at 19:22, Brian West wrote: > I'm just double checking.. I was told it wasn't possible but i'm going to > ask just in case. > > Can you set outbound callerid on a channelized T1? > >I think there is a way to do something like DID with the 4 digits of >DTMF passed before the call. It is unlikely though that you will find >someone interested

I've some DID's that I'm using for in-bound faxing, but I'm having some trouble with getting that working perfectly on my T1. So I'm thinking of pointing them to an analog line. Will the DID's simply come in over the analog, presumably sending the DID digits via DTMF? Or is that not something that'll work? Thanks, -Ken

Hi List, I need to change my provider, at this time Asterisk box is on VOIP trunk. I have two options, T1 or 15 analog lines. I have some experience with analog and I have had two main issues with it. first is echo (I have not tried HPEC yet) and second unpredictable volume. The question is, if I use TE100 with PRI , will I have same issues? I would appreciate any comments and sample zaptel.conf

I'm trying to hook up a non-PRI fractional T1 using a T400P port. The Telco says that it is provisioned as AMI with SF (not ESF) and that they are signalling by "sending down a straight DS1" (I'm not sure what exactly that means). They are also sending DNIS over these channels. I currently run it through a channel bank for my IVR application and it works fine but I am now

https://bugzilla.mindrot.org/show_bug.cgi?id=3589 Bug ID: 3589 Summary: ControlMaster auto, persist and -f fail. Product: Portable OpenSSH Version: 9.3p1 Hardware: amd64 OS: Linux Status: NEW Severity: minor Priority: P5 Component: ssh Assignee: unassigned-bugs at mindrot.org

> Post your extensions.conf and what's on the CLI (asterisk -r) As requested: # cat /etc/asterisk/extensions.conf [incoming] exten => s,1,Answer() exten => s,n,NoOp(CallerID is ${CALLERID}) exten => s,n,NoOp(DID is ${DNID}) exten => s,n,Background(enter-ext-of-person) exten => 1625,1,Playback(digits/1) exten => 1625,n,Goto(digits/1) exten => i,1,NoOp(CallerID is

OK I am going to do it again. Global Crossing is now sending ANI but it is not in the format I expected. Any one know of a way to get this data into two seperate variables? The first number is ANI and the second is DNIS so it is "*tendigits*tendigits* on one line like below. < Called Number (len=26) [ Ext: 1 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan