similar to: Connecting * to a PBX throught a PRI.

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the

Have you tried to load the driver with ec disable? Last time (long time ago) when I was working on a quad card, we weren't able to get ec to work with hardware ec on. ________________________________ From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Brian Alexander Sent: Thursday, September 27, 2007 10:59 AM To: Asterisk Users

Deat all, I am in middle of integrate Asterisk with Toshiba astrata legacy pbx. Following is my setup *Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX* A =============================================> B C <============================================ D Asterisk PBX and strata PBX connected using back to back E1 cross cable. Physicall connectivity

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

Good Day All, I am experiencing some weirdness using the E&M channel and hope you can offer a little assistance with the problem I am having. 1) call comes into channel 25 (Second Span first channel of a Digium Quad PRI from SBC-PRI) 2) Call is sent to channel 1 (First Span first channel on the Digium Quad PRI connecting an ADTRAN via E&M Feature Group D) 3) Between rings one and two

Hi, I have two t100p cards installed. One card connected to the PSTN, the other card is hooked to the Definity PBX with a T1 cross over cable. The card connected to the PSTN works fine. The problem is with the card hooked up to the PBX. The light behind the card is green, but when I dial from this card I get an error. Its says it could start the D-Channel. Could someone help me out with this

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

Hi Guys, I'm looking for a light on the next problem integrating an Asterisk server with a Panasonic PBX using a PRI. The follow config has been working for two weeks and works almost fine, except for some little problems... 1- PSTN provides the E1/PRI (EuroISDN) 2- Asterisk receives the PRI 3- Asterisk provides a second PRI to Panasonic 4- Panasonic receives the asterisk PRI People can

I am trying to test out my PRI configuration on a server by conection another asterisk server to it. I have the T-1 cards up and both set to bchan=1-23 and dchan=24 in zaptel.conf I am getting lost on the signalling in zapata.conf. using pri_cpe makes sense for my target box, but I am getting the following errors on my source box if I use pri_net or pri_cpe signalling. May 31 17:15:06

I have TE405P span connected to a patton/digi 2977 T1/PRI port. Zaptel starts up fine without any errors. Libpri is installed as well. But I get the following when trying to load asterisk ------- Jul 3 19:30:26 ERROR[8192]: Signalling requested is PRI Signalling but line is in Unknown signalling 896 signalling Jul 3 19:30:26 ERROR[8192]: Unable to register channel '25-48' Jul

Hi, I'm seeing rather odd behaviour on a new box with TE110P card. I'm running the TE110P span with ccs,hdb3,crc4 in pri_net, connected to a second machine with a TE410P in pri_cpe. The span is idle. I'm using pri intense debug span 1 and can see the RRs going back and forth. So - things are running along with the span showing "Provisioned, Up, Active" in pri show

Hello - I have (finally) obtained a fair amount of success in connecting my Intertel Axxess PBX to an asterisk box via a T1 PRI. I can place calls from the Intertel side through the T1, out to an IAX2 softphone and the calls get routed correctly and all of the CID information stays intact. However, when I call from the IAX side to an extension which should route back through to the Intertel

Is it possible to send CLID NAME on a PRI? The numbers we send out are being received by telco and propagated, but the names we send out are not showing up. Is this a feature in PRI? Do we need to set PRI_NET instead of PRI_CPE? Is this just not possible? Is this a telco config issue? Thanks for your help... I've read voip-info, and various other sources, and search engines, and google...

> > > Hi, > > > I checked by changing to from-zaptel, but no luck yet. Pls guide me on > this. > > Regards, > vudura senadeera > > > ------------------------------ > > > > Message: 9 > > Date: Fri, 19 Jan 2007 16:47:18 -0000 > > From: "Robert Jenkins" < raj@jrw.co.uk> > > Subject: RE: [asterisk-users]

Hi, I am using Asterisk with various brands and models of SIP phones. Especially the Welltech phones LP201 are particularly nasty with volume and echo. Even with the input gain (microphone) of the Welltech set to the max, the PSTN end can hardly hear the SIP user on incoming calls. Ztmonitor also only gives a level of around 3 === from the SIP phone. I have to increase the rxgain and txgain

Hello, I'm having problem with a wildcard TE110P. As soon as I load the module (wcte11xp for kernel 2.6.10), it spawns a yellow error with or without an E1 plugged-in. Any one managed to set it up in France? Here are my files: zaptel.conf: span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 zapata.conf: [channels] language=fr context=default switchtype=euroisdn pridialplan=unknown

Hi, I am using asterisk 1.2.5 and have some problems with asterisk connected with an E1 card to our PRI. Dialling in and out generally works. When someone dials in from a mobile phone, all numbers are sent as a block, and the called extension rings as intended. when someone picks up his phone handset, waits for a dial tone, and then dials in manually, the call will be redirected to the

Hi there I have a TE110P card fitted in my linux box running : Linux version 2.6.9-5.ELsmp (bhcompile@decompose.build.redhat.com) (gcc version 3.4.3 20041212 (Red Hat 3.4.3-9.EL4)) #1 SMP Wed Jan 5 19:30:39 EST 2005 I followed the installation steps on digium website...no errors reported. The modules seem to have loaded...here's what lsmod shows: Module Size Used by

hi, i'm having problems getting asterisk spliced between an E1 PRI (german Telco Arcor) and an Ericsson Business Phone 250 digital PBX. The Asterisk Server has a TE405P with it's port 1 connected to the E1 PRI provided by our telecommunications provider Arcor and port 2 connected to the E1 PRI of our Ericsson BP250. the setup before: Arcor TelCo PRI(E1)

My legacy PBX accepts CID number, but not name. My old PRI vendor never sent the name, so there was never an issue. I have wedged asterisk between the Legacy PBX and PSTN. PSTN - PRI - asterisk - PRI - Legacy. Any calls from asterisk (sip and iax extensions) which have callerID set, will not connect. The legacy PBX hangs up, but asterisk thinks that it is still ringing. I have added