similar to: Channelized T-1 (NOT PRI) Voice and IP mixed

Hi, I was going to order the T100P but it is replaced by TE110P. On further reading the TE110P does not need an external router (The one that separates the data from pstn lines ?). Has anyone got it configured? And on the wiki it says that the drivers for some distros don't exist yet. Is redhat supported? And if I need to connect a fax machine will the FXO cards on ebay work (I know to

Hi list, I have a terrible noise issue with Dell SC1430 + Digium TE110P. The digium card is not sharing interrupts with any other device, as I saw in Dell's BIOS and also with "lspci -vb" command. After changing coax wire, UTP, balum, digium card ... I have found that the problem is in Dell box, so now I'm running the same Asterisk config in other server with the same

Hi Folks, I have a T100P ordered from Digium in the past. Its working perfectly fine but I now need to more the server to India (out-sourcing) and we will be getting an E1 line there. Does anyone know if T100P was capable (upgradeable) or swappable so that I could use it with the E1 lines instead? Any pointers to driver/firmware update would be highly appreciated. Thanks. R -------------- next

> The documentation mentions that the Digium channels can be split into some > voice channels and the remainder of the channels used for routing IP > traffic. > > Does any one have this in use in conjunction with Asterisk? Does it work > well? Would you recommend it for a production server? > > Obviously, if this works, this makes for a cost effective platform where

Hi, I'm trying to connect to Telewest/Virgin Media with a TE110P using asterisk 1.4.13/zaptel 1.4.6. No matter what I try, my span always appears as PRI span 1/0: Provisioned, Down, Active My zapata.conf is currently ----------------------------------- [channels] echocancel=yes echocancelwhenbridged=no echotraining=yes switchtype=euroisdn contect=from-pri signalling=pri_cpe group=1 channel

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

In the next week or so, we'll be turning up a new T1 Pri from Cox Cable in Omaha using a T100P (installed but not yet configured). While discussing the interface parameters with a very knowledgable Cox engineer, we decided on some of the basics including b8zs, esf, dchan=24, callerid, 5 digits of called number forwarded to *, and switchtype=national (NI2). They indicated their CO switch is a

Even though they make the cards and advertise that they support data modes, digium won't support data mode on the $500 card they sold to me, so I must turn to the list. Has anyone configured a T100P to use a T1 strictly as bandwidth? Is there a HOWTO somewhere? Wiki has nothing I could find. I've got plently of public IPs I can assign to it but don't know how. Thanks, Matthew -----

Hey gang, I was successful in recompiling my 2.4.20 kernel to support HDLC. I was successful in hooking up our T1 line into the zap card. I was successful in being able to ping equipment on the other end of the T1. I was unsuccessful in pinging the outside world from the other end of the T1. I've attached a cheezy image of the network. Here is the routing table: [root@asterisk root]# route

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

We are in the process of installing a PRI line and we are going to connect it to an Asterisk Box. Verizon called us today to find out some information. I am surprised that they have never heard of Asterisk or Digium. But anyways, they needed some information in order to set up the circuit. Does the TE110P support NI1 or NI2? (I think the answer is both) What is the number of digits

I am trying to use TE110p card for Euro ISDN with Ericsson AMS switch. I consistently get one of the following errors: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 or PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 My zaptel.conf file: -------------------------------- span=1,0,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=us defaultzone=us

Hi I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts .... I can't seem to find anything in the log that suggests what could be wrong .....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,

We have contracted with Eschelon to provide voice and data over a T1 link. The plan is to terminate this link at a T100P card in the * system. The vendor has said that they will provide the D channel "contiguous to the voice channels" (voice on channels 1-8 and D channel on 9). The data channels would be 20-24. Will the T100P be able to accept this configuration? Does the PRI

Hi, I'm trying to put together an * system with extremely high up time. The system as it stands now is 1 dual p4 with raid, redundant power, etc.. and a T100P card. I would like to get a second similar or identical box with another T100P card. I have 1 PRI, how do I get the second box to take over communication with the PRI should the first box fail? Of course I'd like this to be

Hi, We currently have an Asterisk box (P4 2.4 Ghz, 512Mb RAM, 1 T100P, Zhone Channel Bank and 1 E100P) connected to an ISDN running without any problems. That machine is working for about 1 year. Two days ago, we decided to switch that machine for two PowerEdge 600SC (HA) and we got some problems. The running machine (P4 2.4Ghz) has an Intel motherboard with four 32-bit 3.3v PCI slots,

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

Does anyone know if you can have multiple TE110P cards in one chassis? -Thermal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061011/adbceeb5/attachment.htm