similar to: My Sangoma Experience in Asterisk: Followup

Hello, Several people asked to get a hold of the stats I used to determine that the Sangoma T1/E1 boards performed better in our real-world tests than the Digium boards. We've decided to post our results after confirming them over the past month of operations. Here is a link to the last two reviews I wrote about Sangoma with Asterisk:

Hey! I am installing Sangoma A102D wanpipe driver and i got following error. what is this ? why dir isn't there ? wanpipe-3.5.16 # make dahdi DAHDI_DIR=/usr/src/dahdi wanpipe-3.5.16 # make install ....Send .... .... Installing Wanpipe Firmware update utility in /etc/wanpipe/util/wan_aftup install -D wan_aftup /usr/sbin/wan_aftup install -d /etc/wanpipe/util/wan_aftup/scripts install:

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as

Hi all, I am having a very strange problem. I am terminating a PRI (5ESS switch type, national plan, 23B+1D (24)) into a Sangoma A104 and am not able to produce any audio heard on the PSTN end of the call. Not sure what's wrong - the card worked before under a Trixbox setup. I'm running kernel 2.6.19 (tried 2.6.24.3 but had to downgrade as wanpipe stuff would not compile), zaptel

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

Hello, Have you tried the wanpipe-beta8c-2.3.3.tgz release in the custom/2.3.3 dir on their FTP site? Also, have you contacted Sangoma for support? They are very responsive. I am using wanpipe-beta8a-2.3.3.tgz and it's been working great on my A104 for a week now. MATT--- -----Original Message----- From: Dmitry Zhukovski [mailto:DZH@comx.dk] Sent: Monday, May 09, 2005 5:20 AM To: Asterisk

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Hi again, Well - I didn't see beta8a-2.3.3 in custom dir. Will try. Also I tried to contact Sangoma - they are very fast to answer but main problem is time difference - it's 6 hours between Canada and Europe. Br, dmitry Dmitry Zhukovski System developer ComX Networks A/S Naverland 31, 2 DK-2600 Glostrup Denmark Phone: +45 70 25 74 74 Fax:???? +45 70 25 73 74 Web: www.comx.dk

Greetings folks- I'm experiencing issues with a freshly installed box. When a call comes in via PRI (Sangoma AFT-A104), I see this in my logs: [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 12 (Invalid argument) [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 8 (Invalid argument) [Dec 15 14:26:10]

Hi, My configuration is pri----*(te405p)---iaxclient. My * version is 1.0.7 running on tyan dual opteron board. I have several problems. 1) inbound echo For outbound call(iaxclient-->pri), there is almost no echo. But for inbound(pri-->iaxclient), I can hear distinct echo. Can Sangoma a104 or digium te406p help this problem? 2)Today i received te406p. I know T1/E1 jumper. But how can i

Hi, I migrated from asterisk 1.6 to 11.3. The Server has a Sangoma A104 quadPri card installed. OS is a fresh installed Ubuntu 12.04 64bit libpri, dahdi etc. all latest releases.. Sangoma says... driver is compatible with ANY asterisk version... I tried driver 3.5.8... Setup ended with error. I tried (latest) driver 7.0.1 Setup went through, Asterisk is showing dahdi channels... all fine....

Hi, I learned about shorewall a few days ago and am quite impressed with how easy it was to create a powerful firewall. I set up a test system with a cable modem and it worked flawlessly. I''m going to be building a Router/Firewall for a new T1 that will be using a Sangoma WANpipe card w/ integrated CSU/DSU to connect to a T1. Has anybody done this yet, or do you know if it''s

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

Howdy, Just installed a new switch in a new location (Ubuntu, 2.6.24-24 kernel, zaptel 1.4.12.1 built from source, libpri-1.4.10.1 built from source, asterisk 1.4.26 built from source, wanpipe 3.5.4 built from source, Sangoma A104d with firmware that is probably a year old). I plugged in an RBS T1, ESF, B8ZS, wink start, and MF signalling. I stuck with the defaults that the wanpipe build

I am having a problem with asterisk not being stable enough for production use. I have two cards, the digium TE406P, and the TE410P. The TE410P is the primary card that I am using but I would like to move to the TE406P for the echo cancellation and more flexibility of PCI slots available. General config info: 3 PRIs, configured as such: span=1,2,0,esf,b8zs span=2,0,0,esf,b8zs

Hello List I am having a rather big problem with a sangoma A104 card, I just installed to replace a Digium TE410 card, that was acting up. But now we have a problem with the sangoma card. It runs great after being started, and calls proceed as normal, but after about 1 hour, it stops being able to make and receive calls. If I run wanpipemon debug, can see that the card still receives

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name |

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS

Hi All i'm using sangoma card. connected to E1, my wanpipe file as #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Fri May 27 00:25:04 GMT+7 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended