similar to: IAXy Firmware Upgrade

I've googled and grepped myself silly. I see the iaxy.bin file there in the contrib tree of the asterisk source, but nowhere have I been able to find out how to get it sent to the device. . . Anyone know? Thx. B.

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

I am having trouble with a DTMF-based application on Asterisk 1.0.3. Specifically, when two IAX2-based devices are talking, when they send DTMF to eachother, the other side only hears clicks, and maybe a millisecond of DTMF tone, but not any real duration. Furthermore, when one IAXy device calls the Echo test program, we can hear our echo, but when we punch DTMF in, we get the same effect

Digium has discontinued their ATA iaxy adapter; don't blame them, too expensive so they can not compete. The adapter is upgraded automaticaly when it is connected to new asterisk version; since this adapter is discontinued will it still work with asterisk 1.6 and beyond or will it be\ just a "door stopper"? -- Joseph

I've heard comments about the instability of the IAXy (loosing IP, locking up, etc) . I want to deploy some, in a remote site. The comments on the instability suggest that the simplest approach is to power-cycle them when you have problems. The IAXy would only be in use from 3PM to 8 PM. My potential simple solution is to have a timed power brick (like what you would use for a block heater)

http://www.x100p.com/products_2.htm Anyone ever use this box? How's it compare with the Iaxy? I'd like to buy one or the other.. The Iaxy is appealing because to me, it seems less "no name", but this one says that it supports using hostnames, whereas apparently the iaxy only supports IP addresses?? That's appealing to the dynamic DNS guy in me! :-) Any

In the mailing list archives, I found a message that indicates that the IAXy has the ulaw, alaw, and g726 codecs, but I cannot find anything official on Digium's site about it. The Installation Manual has an example iax.conf file that indicates the ulaw codec, so I know that one is good. But we are thinking about using the IAXy over a VPN, to replace our MultiVoip. alaw and ulaw are

I place a call from an IAXY to an IAXY device. INitially the calls show in the output of "show channels". Then after a few seconds the "show channels" command shows 0 active channels even though I am still talking on the channels. Any ideas on this? THanks, Jerry

Hi, methinks that in the good 3 months since i ordered an IAXy, things have changed so much that now almost anybody out there with a VoIP hardweare website offers complete phones for less money than the IAXy, with support for both IAX2 and SIP in many cases, and fully configurable via its own keypad. What would you recommend as a rugged, small, and easy to configure/use self-contained unit that

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

Hi! Could someone please tell me where in the CVS tree the IAXY firmware is and the utility used to install/flash the IAXY? Or a perhaps cvs command that shows me which directories are available in the CVS? I did 'man cvs' but can't find such a command or flag. Also is there any documentation for the IAXY in the CVS tree or anywhere or C comments I can read somewhere to glean some

Hi all, The firmware I used is pa168s_iax2_us_151011.bin. My problem is the handset dial before I finished key in all the numbers, no matter how fast I managed to press the keys. It appeared it always dialed immediately, for example "011862", when I actually ment to dial 0118620xxxxxxxx. Thus left the remaining numbers "0xxxxxxxx" unsent. The handset had its dial plan

Hi, hoping that experienced hands will quickly show me the right way: after a fruitless web search i am turning to this list with my rather elementary question: is there any other way to communicate with the IAXy besides using special utility software that needs to be compiled under UNIX? Here is the story: about two months ago, after some not very satisfactory attempts at using SIP (my phone

I just bought a new IAXy box and am only achieving one way calling. Both iax.conf and the IAXy support ulaw and gsm. When I try to call, however i get this error: Feb 11 15:20:32 NOTICE[7963]: channel.c:1893 ast_read: Dropping incompatible voice frame on IAX2/iaxy-2 of format ilbc since our native format has changed to ulaw I added support for ilbc on the IAXy and in iax.conf and am still

Hi, Has anyone got faxing working via an IAXy? I'm having trouble getting it working with a fax machine here. The IAXy works fine, I can make incoming/outgoing calls via it, however our PDQ takes a few redials to get data over to the dialled party, and faxing doesn't seem to work at all. I have turned off all the echo cancellation stuff, just in case that was an issue. Anything I

I need a cheap simple adaptor for analog phones to use with Asterisk. It should be some kind of "configure and forget" type of device, to use at the office, or just throw it in a road warrior's bag and use it while travelling, to call back to the "mothership". I can't decide between iaxy and sipura. Can you guys help? Which one would you use? (and why?) I feel that iaxy

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

iH i have an IAXy which i can make calls from but am unable to call. when i dial the extension assigned, i get the following from the console; -- Executing Dial("SIP/5801-b665", "IAX2/5899@192.168.0.5") in new stack -- Called 5899@192.168.0.5 -- Call accepted by 192.168.0.5 (format ULAW) Nov 1 12:28:33 NOTICE[163850]: chan_iax2.c:5546 socket_read: Rejected

Hi all, getting a server going wiht a few TDM400's and some phones, and some IAXys too I haven't heard any issues about AU phones being able to RING in Australia, like the problem in the UK with ring capacitors on the BT system. Are there any problems like that? Also, with the iaxy's -- they should work (and ring) in Australia right? The only hint I'm seeing around is the use