similar to: 8 channel fxo setup outgoing call

I have an eight channel fxo setup (2 TDM400P cards) and I have them setup. Here are my configs: Zaptel.conf: fxsks=1-8 loadzone=us defaultzone=us Zapata.conf: [trunkgroups] [channels] musiconhold=default rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callerid=xxxxxx callwaiting=yes busydetect=no callprogress=no usecallingpres=yes callwaitingcallerid=yes

Ok, I just got my 8 channel setup to dial out and back in but here is the new issue. It sill dials in fine with all the channels, but dialing out from inside the asterisk system only works on the 1st channel of my 1st TDM400P card. Now I dont have all 8 PSTN lines going into my asterisk box at this moment, only one line for testing currently, but I should be able to plug that one line into any

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

Hi all, I have a surplus Sangoma 10 port FXO card for sale. This model could be upgraded to 12 ports or even changed to FXS or a combo of FXO/FXS by changing the grand-daughter cards (each card supports 2 lines). You could also "downgrade" the card by removing any or all of the daughter cards. I'm asking US$450 plus shipping to the lower 48. Paypal or Master/Visa only. Thanks

At the cost of breaking the thread I'm going to change your subject and replace 'Principle' by 'Principal'. I just can't stand it any longer... OK, here is how I would solve your other problems. First put > wh <- c("USA", "New Zealand", "Dominican Republic", "Western Samoa", "Cook Islands") > ind

Is the Wildcard X100P still supported? I have one sitting around that I bought 3+ years ago and never used it. I need the functionality now. Before I run off and buy something new, I'm curious if this will "just work". I also have an old TDM400P with 2 FXS modules that I bought at the same time. Then, there was no FXO module for the 400P. Will a TDM400P this old support a

Dear R, I'm trying to plot the first principle component of an analysis vs the first variable but am having trouble. I have no trouble doing the initial plot but have difficulty thereafter. First I want to highlight some points of the following data set list(running) [[1]] X100m X200m X400m X800m X1500m X5K X10K Marathon Argentina 10.39 20.81 46.84 1.81

Hello, I have a Dell PowerEdge 2850 that periodically (6 times in the last 24 hours) freezes, requiring a power cycle in order to come back. The machine is running a Xen 2.0 stable source install. Here is the appropriate Grub entry: title Xen 2.0 / XenLinux 2.6 kernel /boot/xen-2.0.gz dom0_mem=131072 module /boot/vmlinuz-2.6-xen0 root=/dev/sda1 ro console=tty0 Dom0 boots happily, and new

Hello! After upgrading my production machine to 1.2.1(used to be 1.2.0) on friday i experienced strange behaviour yesterday, i received deadlock-avoided-messages and channels refusing to hangup on span1(used for inbound calls), both messages in all cases paired: Jan 9 17:40:01 WARNING[30003] chan_zap.c: Ring requested on channel 0/17 already in use on span 1. Hanging up owner. Jan 9 17:40:01

I have seen this in the archives any number of times -- but I have yet to find a solution that works for me. Any suggestions you can offer would be most appreciated. Here are the answers to the questions I have seen asked in earlier posts. The log contains: Mar 10 12:26:29 WARNING[3015] chan_zap.c: Unable to specify channel 4: No such device Mar 10 12:26:29 ERROR[3015] chan_zap.c: Unable

Hi All, Channels 25-28 on a customers PBX are regular Zaptel FXO cards that are hooked into 4 incomming phone lines. They are all in a group to do automatic rollover for outgoing calls (if channel 25 is being used, dial on channel 26, etc.). Sometimes when a user is dialing a number, instead of bridging to one of the FXO cards it goes and rings to Zap/1-1. This doesnt occur all the time but some

Dear R Should I be concerned if the loadings to a Principle Component Analysis are as follows: Loadings: Comp.1 Comp.2 Comp.3 Comp.4 X100m -0.500 0.558 0.661 X200m -0.508 0.379 0.362 -0.683 X400m -0.505 -0.274 -0.794 -0.197 X800m -0.486 -0.686 0.486 0.239 Comp.1 Comp.2 Comp.3 Comp.4 SS loadings 1.00 1.00 1.00 1.00 Proportion Var 0.25 0.25 0.25

Trying to config the latest Asterisk/zaptel with an Digium Wildcard and a single X100m FXO interface connected to a POTS analog line. Build and install of both work ok - I'm using Suse 8 on a dual Pentium box. I load the driver with "modprobe wctdm" and the LED on the wildcard lights up. Then I start Asterisk with "asterisk -vvvgc" and asterisk fails to start. The

>Asterisk and it works fine untill the following >situation: > >- one of the telco lines occasionally becomes mute after call is completed, would not provide dial tone, (not sure about ringing on that >line) - both via old and new PBX. >- zap show channel <n> would show that line as 'Offhook', though no telephone is off hook. > >If physical line would be

Hello, I've got a problem with something I'm doing and can't seem to figure it out. I've tried different suggestions I've found on voip-info.org as well as other sites but nothing I do seems to work. I've got an older Digium TDM400P. The FXO daughter card is connected to my POTS line and the FXS daughter card is connected to a TDM phone. I also have multiple SIP

I have been having some troubles with the zaptel channel on what appears to be the inbound process. The box is running the stable CVS code and has a TDM400P 4-port FXO card in it for analog connectivity. Channel 1 is the only active port on the card at the moment as we only have one analog line. What has been happening is that it looks like Asterisk has been detecting an inbound call even though

Listmates, No response from the suse list, so I am trying here. I bought a new HIS Radeon x1650 card for my daughter's computer, and I cannot get the card to work with compiz. I thought I knew the fglrx driver pretty well, but I am stumped here. The card has 512M of Ram and sits in the AGP slot of an MSI KM2M board running openSuSE 11.0/KDE 3.59 and compiz-0.7.6-16.1. All bios setting are

Andreas, As far as I can tell (/conjecture), this is because the list of classes a particular class inherits from directly is appended to as needed, and so the order that a class extends others isd refined by the order that those connections are defined. We can see this with two setClassUnion calls, rather than required setAs: > setClass("grandma", slots = c(a =

Please explain the relationship between modules from the driver (wctdm), the /etc/zaptel.conf file and zapata.conf. Specifically, if I have a FXS module 0 and FXO module 1, what should be used in zaptel.conf and what should be used in zapata.conf? Then finally, in extensions.conf, what is the Zap channel for dialing out? Zap/? % dmesg Module 0: Installed -- AUTO FXS/DPO Module 1: