similar to: 8 channel fxo setup outgoing call problem

Ok, I just got my 8 channel setup to dial out and back in but here is the new issue. It sill dials in fine with all the channels, but dialing out from inside the asterisk system only works on the 1st channel of my 1st TDM400P card. Now I dont have all 8 PSTN lines going into my asterisk box at this moment, only one line for testing currently, but I should be able to plug that one line into any

I have a Asterisk @home ver 1.0 running with a TDMB11 card. Several sip extensions and a regular phone connected to the box. All routing works fine from the regular phone connected to the box, whether its going to FWD, broadvoice or the PSTN. The problem I am experiencing comes from making calls from the sip phones. They get routed correctly to the sip and iax trunks but when making calls

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

My outgoing FXO calls are answered but have no audio in either direction if I have callprogress=no in chan_dahdi.conf. If I change to callprogress=yes then the audio returns. My chan_dahdi.conf file is listed below. Can anyone point-out why callprogress=no isn't working? #cat /tmp/a [trunkgroups] [channels] language=en context=incoming toneduration=40 ;usedistinctiveringdetection=yes

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

What is involved in provisioning Asterisk to use a multiline analog service from our local telco? I will only have one twisted pair entering in on a OpenVox card but am not sure how Asterisk interprets and deals with two incoming calls and/or two outgoing calls? Thanks! jlc

Hi, I've got an Asterisk system that I've just added an X100P card to. Incoming calls route to my call group just fine. When I make outgoing calls by prefixing with 9, they route to the PSTN network okay, get answered but then drop straight away. Has anyone seen this before and found a fix? I'm in the UK using a phone line from NTL. I've Googled for a bit, can find others

Dear all, i have a problem with a system running - Ubuntu 10.04 ( all updates done ) - ii asterisk 1:1.8.5.0-1digium1~lucid Open Source Private Branch Exchange (PBX) - ii asterisk-dahdi 1:1.8.5.0-1digium1~lucid DAHDI devices support for the Asterisk PBX I also use freepbx 2.9 for the configuration. Hardware is a Dell R410 and a Digium

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

It said 'include zapata-channels.conf', where this line wasn't commented bij the ';'... Could you post me a working example of such a config (or a part of it, for the X100P cards...? Thanks guys! Message: 9 Date: Sat, 19 Mar 2005 18:04:26 -0500 From: "Jeff Glassman" <jrglass@columbus.rr.com> Subject: [Asterisk-Users] newbie question To:

Hi there, I have a new box setup using the latest version of FreePBX and the latest SVN of Asterisk 1.2 as of yesterday. Incoming calls from our PRI work fine. However, outgoing calls gives me the operator saying "The call cannot be completed as dialed" after two rings. Here's an outgoing call from extension 271: -- Executing Set("SIP/271-09f61dc0",

hi all! I'm running an Asterisk-box with bristuff-....RC8n and 2 HFC-S cards. I m located in Vienna/Austria. I have the problem that on outgoing calls i hear my voice as a short echo (about half a second). This occurs not on every call. I tried some changes in my zapata.conf, with rxgain and txgain settings, but to me its hard to find a configuration which is good for every call i make. Is

I am using asterisk 1.4.21 with outgoing call files. I am call a line that is busy as you can see below. How can my AGI ask what the status of the last call was so I can tell if there was NO ANSWER or it was BUSY? Thanks, Jerry -- Attempting call on SIP/401 for smvoice_callprogress at smvoice-dialout:1 (Retry 1) -- Got SIP response 486 "Busy" back from 192.168.1.161

I'm not sure what you mean, I had one card with one FXO in it and it worked fine. Now, we have 2 TDM400P cards with all of their slots filled with FOX chips and I can't make out going calls. Those are the only 2 cards on the system, the rest is just motherboard. -----Original Message----- Do you have ATI FXO daughter cards. We had experienced similar problems. After replacing the ATI

I'm having trouble getting outbound calls going with aah 1.3 and a tdm400p w/ 4 FXO. Incoming calls work fine, outbound I get this: -- Executing SetVar("SIP/231-af2b", "OUTNUM=6643955") in new stack -- Executing Cut("SIP/231-af2b", "custom=OUT_1|:|1") in new stack -- Executing GotoIf("SIP/231-af2b", "0?19") in new stack

i have a prablom here, i want to send a call from A to B use sip trunk , the call can sended B,but not work to PSTN. the message from B server. help pls,what's rong? > > <--- SIP read from 192.168.0.176:5060 ---> > INVITE sip:15921256331 at 192.168.0.151 <sip%3A15921256331 at 192.168.0.151>SIP/2.0 > Via: SIP/2.0/UDP 192.168.0.176:5060;branch=z9hG4bK51a51b96;rport

Greetings *`s, I am manually creating call files and dropping them into /var/spool/asterisk/outgoing to be picked up by *. Presently, when I use local/internal parameters using SIP it works..ie I make an internal call from device to device. However, when I try dial an outside number which I have set up in a custom conf file, it bombs out with the following message :

Hello, I have an issue with Digium TDM 400 card series. When I try to make outgoing call (PSTN call) for example, the Zap channel could not be created and busy channel message appeared. Below is the full log : [Feb 5 09:26:17] VERBOSE[3047] logger.c: -- Executing [s at macro- dialout-trunk:20] Dial("SIP/213-09648720", "ZAP/g1/08170709XXX|300|") in new stack [Feb