similar to: IRQ headaches

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

Hi, I have an asterisk installation with 2 E1 cards Software version is Asterisk 1.2.6 Libpri 1.2.2 Zaptel 1.2.5 I'm having problem with fax transmission, let me explain better my setup: My fist TE110P E1 card is connected to the telco line the second TE110P E1 one to an Nexspan PBX so the server is basically sitting between the line, and the pbx. every call coming from the line is

These allow and disallow work with NuFone for me disallow=all allow=ulaw allow=alaw allow=gsm Jeff Message: 11 Date: Fri, 11 Mar 2005 11:15:51 +0100 From: "Edward Banfa" <edward@radform.com> Subject: [Asterisk-Users] NuFone Configuration [problem] To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" <asterisk-users@lists.digium.com>

I have a pair of sites tied together with a T1 line running zaptel PPP on either end. The system works, but I keep getting these messages in the kernel logs, and users are reporting connection problems (TCP timeouts, and hangs) especially under high usage. --snip-- HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC

Hi, I'm curious what chip Digium is using in the latest TDM400 cards. Specifically, to my recollection, they used to use the TigerJet 320G, however somewhat recently, Tigerjet was bought out, and now the 320G is no longer produced. Maybe a better question is: is there a way I can take the latest DAHDI source and get a list of supported chipsets from it? Thanks. MCH -------------- next part

Heya Mark (and others), Here's an update on my adventures while trying to debug the Zaptel-related panics, as discussed on this list a while back. While debugging the problem, I completely swapped the machine for an entirely different model (Supermicro dual Xeon 2.4GHz with 2Gb of RAM), put the cards in, recompiled * + Zaptel and administered my stress-test. The machine stayed up in excess

I have seen this posted around the list a few times, but have never found my exact error or even a solution to this. I was getting this error every few seconds...... After moving the card to a different PCI slot and turning off some devices that are not needed. I was able to get the messages down to about every 10 minutes and the T1 card now is sitting in it's own intterupt. Apr 25 23:49:15

Hello all, i'm experiencing a list of unpredictables hangup on SIP phones using a PRI E100P Card. All i can see in logs is " WARNING[81931]: File chan_zap.c, Line 5402 (zt_pri_error): PRI: Read on 37 failed: Unknown error 500" I receive a lot of these errors in asterisk/messages. It doesn't seem to be strictly linked to hangups, since i have dozen of these messages per

Due to some failed hardware on another platform, I've had to move a T100P card to a different chassis. After this move was completed, I am seeing some strange results on the T100P card that do not display to me any failure mode with which I am familiar. The card comes up, and shows "good" carrier and status, but Asterisk refuses to bring the D-channel up. Calls of course do

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

I know, I know, check the archives but I can't find an answer since the new cards are well, NEW! I understand the whole issue of expandability and flexibility of using a T1 card and an Adtran 750. FXO or FXS, you mix and match. With the new card offerings from Digium I can easily put a 4CO by 8 Station system together. Barring the extra interrupts, extra CPU Cycles of extra interfaces, is

Hi, I've compiled Asterisk cvs stable (few days ago) unde Suse 9.2 without any problems. We're using te110p and wcte11xp module that is autoloaded by Suse 9.2. Card goes green after reboot, but this meesages appear in logs: Mar 22 11:28:51 linux kernel: Zapata Telephony Interface Registered on major 196 Mar 22 11:28:51 linux modprobe: FATAL: Error inserting torisa

Guys.. I just noticed that my grandstream handytone 286 ata are having problems with voice cutoffs... We can listen to the person on the zap channel (x100p cards) without problems but they sometimes listen to us with cutoffs.. like "He ...lo..... ow...r.. you" and it comes and goes.. this doesnt happen all the time but often enough. Any ideas what might be happening or what do I need

My PRI is being reset at least once a day with the following errors in the logs. zaptel, zapata, libpri, and asterisk are from CVS this morning.. This has been happening for weeks on all versions (including -stable). the T100P card appears to NOT be sharing an IRQ. xenon# cat /proc/interupts CPU0 0: 1203977 XT-PIC timer 1: 3 XT-PIC keyboard 2:

Since updating * via CVS earlier this week, I've been having problems with cdr_mysql. Prior to that time my queries and cdr all worked fine. Now, even though my queries still work, I get the messages similar to this: ERROR[1211374384]: cdr_addon_mysql.c:203 mysql_log: Failed to insert into databas -- Hungup 'Zap/74-1' Anyone have any suggestions what went wrong?

Hi All, I have an equipment loaded with 4 X100P (numbered 1-4)) and one T400P (numbered 5-8). Everything works fine except that I cannot use one of the FXS ports (number 5). If I configure zapata.conf to recognize it, the whole system voice quality suffers. I've tried already to switch PCI slots, with no results. Below is a snapshot of my /proc/interrupts, maybe this can shed some light on

Hi, Every time I dial into my asterisk box i hear nothing but asterisk jittering. The following is an example of what I get on the asterisk CLI Thanks *CLI> DEBUG[81926]: File chan_sip.c, Line 3826 (check_user): Setting NAT on RTP to 0 DEBUG[81926]: File chan_sip.c, Line 4807 (handle_request): Check for res DEBUG[81926]: File chan_sip.c, Line 952 (find_user): Call from user

We just had * crash on us - no calls could be made / received. We had to kill -9 the * process. Checking the error logs, I came across these two lines, with the times matching the crash: Aug 26 13:48:00 WARNING[19282] pbx.c: Local/6024@AgentQ-94ce,2 already has PBX structure?? Aug 26 13:48:00 WARNING[19282] channel.c: Thread -1105359952 Blocking 'Local/6024@AgentQ-94ce,2', already

Hello All, I am getting a set of errors when I boot Asterisk that I have not been able to solve. What is causing these error(s)? Asterisk boot output: ============== Asterisk CVS-04/10/04-21:44:51, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= [