similar to: Caller ID on E&M Wink

Ok, I'm about to take the plunge, and am trying to decide between Channelized T1 E&M and PRI. I'm getting an "Integrated T1" which will have data and voice capability, all plugged directly into my digium single T1 card. In either case the data piece looks pretty straighforward, just setup the channel properly, hand it off to the linux hdlc layer, and route away.... the

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

I receive calls over a T1 with callerid and then *ani*dnis*. I am able to strip out the ani and the dnis in the dialplan but when I try to set the caller ID to be the ani, it looks ok but then if I do a NoOp callerid on the next line, I get unknown. Here is the section of my dialplan: exten => _*NXXNXXXXXX*NXXNXXXXXX*,1,Set(ANI=${EXTEN}) exten =>

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm

I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound

Hey folks, I'm pulling my hair out on this situation and would welcome some advice: I'm using the AMI Manager to Originate calls onto 2 E&M wink T1 circuits via a T4XXP card from Digium. Everything works fine for about 600(+/- 50) calls then the Manager is suddenly unable to launch calls. Using ZapBarge to listen to the channels themselves you can hear the dtmf digits being dialed,

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

I am preparing to connect an asterisk box with a redfone fonebridge to a T1 service provider. I am doing this by testing first with another asterisk and a Sangoma card playing the role of telco. I formerly had this test configuration operating flawlessly as a PRI connection. But I discovered that I will need to use E&M, thus I've chosen the parameters as described in the subject

Has anyone here used T1s with RBS with asterisk? Cary Fitch

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

Howdy, New installation, trying to connect an RBS T1 with AMI/D4 framing and E&M Wink. Using a Sangoma A102d and asterisk 1.4.22-2 on Centos5 (Trixbox 2.6.2.1). Outbound calls work fine, but inbound calls fail to read the DID information, and with debug set to 10 I get the following: [Feb 2 19:40:23] DEBUG[25184] chan_zap.c: Monitor doohicky got event Wink/Flash on channel 3 [Feb 2

I currently have Asterisk deployed in my office with a TE411P. On the first port of this card is a T1 from the telco setup for D4 AMI. Unfortunately, I'm not receiving caller ID on inbound calls from this line. The caller ID information is arriving in the form *ANI*DNIS*. In zapata.conf, I have signalling set to em_w. The DNIS always arrives correctly, but I'm never receiving the ANI

does anyone know how to route a call coming in with ANI*DNIS* Oct 31 12:47:41 VERBOSE[30056] logger.c: -- Executing Set("Zap/49-1", "DID=1231234*4812*") in new stack I tried making a route for _.*4812* but that matched everything rather then just the dnis i wanted.. any ideas? I would preferably like pass the callerid along to my extensions, but for now the important

Hi List, I have some T1 750s; hookup via a T1 to a TE420P card. We have them all set as E&M wink trunks. We get a dial tone and can call numbers, but when i call another number the ringing I hear on my phone is very weird, its not the standard ring tone. What will cause this? Is this a * setting or something in the Adtran I am fixing, I just want good ole ringing to be heard! Any help would

List: I already have asterisks up and running on a PRI, but where we are moving we cannot get a PRI so we are going to get T1. My question is: We are going to us E&M Wink for signaling with DTMF and caller id. The channels are going to be setup like this, 12 channels for 2-way and 12 channels for incoming only with DIDs. How would I configure the zaptel.conf? I realize that I will have two

I'm trying to get a patch tested for inclusion in CVS. Anyone that is running E&M on a T1 and had to fool around with emdigitwait could you please try this. This patch removes the need for the emdigitwait parameter and speeds up dialing. This situation is mostly interfacing a legacy PBX/Key system with Asterisk. I've been running a couple of systems with this patch for