similar to: Voice getting cutoff

Hi All, I have an equipment loaded with 4 X100P (numbered 1-4)) and one T400P (numbered 5-8). Everything works fine except that I cannot use one of the FXS ports (number 5). If I configure zapata.conf to recognize it, the whole system voice quality suffers. I've tried already to switch PCI slots, with no results. Below is a snapshot of my /proc/interrupts, maybe this can shed some light on

Since updating * via CVS earlier this week, I've been having problems with cdr_mysql. Prior to that time my queries and cdr all worked fine. Now, even though my queries still work, I get the messages similar to this: ERROR[1211374384]: cdr_addon_mysql.c:203 mysql_log: Failed to insert into databas -- Hungup 'Zap/74-1' Anyone have any suggestions what went wrong?

I know, I know, check the archives but I can't find an answer since the new cards are well, NEW! I understand the whole issue of expandability and flexibility of using a T1 card and an Adtran 750. FXO or FXS, you mix and match. With the new card offerings from Digium I can easily put a 4CO by 8 Station system together. Barring the extra interrupts, extra CPU Cycles of extra interfaces, is

Hi, Every time I dial into my asterisk box i hear nothing but asterisk jittering. The following is an example of what I get on the asterisk CLI Thanks *CLI> DEBUG[81926]: File chan_sip.c, Line 3826 (check_user): Setting NAT on RTP to 0 DEBUG[81926]: File chan_sip.c, Line 4807 (handle_request): Check for res DEBUG[81926]: File chan_sip.c, Line 952 (find_user): Call from user

Excuse my ignorance here, but I am desperately trying to isolate the IRQ for my TE110P card (shown below as t1xxp) Ive gone into my bios and disabled all usb , parallel, serial and some other devices, those that I needed to keep, I have moved off of IRQ 10 and onto IRQ 5, but everytime I boot up, I get usb-uhci and ehci_hcd using IRQ 10 as well as my Digium card. Does anybody know what these are

Hello All, I am getting a set of errors when I boot Asterisk that I have not been able to solve. What is causing these error(s)? Asterisk boot output: ============== Asterisk CVS-04/10/04-21:44:51, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= [

Heya all, I'm experiencing some problems with a TDM40P and was wondering if anyone else on this list has similar experiences, or maybe even a possible solution. My setup is a dual PIII-750 with 1 gig of RAM, with an X100P, connected to an analog line to my telco, and a TDM40P with analog phones connected. The TDM-card is not sharing any interrupts, but the X100P is, with the 2 Adaptec SCSI

The USB core was completely rewritten in 2.6, and as such the functions that ztdummy depends on do not exist in 2.6. I get the feeling that these changes are too much to easily fix ztdummy, so I don't expect to see it working on 2.6 any time soon (if ever) I made some small changes to zaprtc to work on 2.6 and I have MoH and Meetme functions working fine in my lab. For production I would

PC: HP Vetra VL400 Mainbood: Intel815 BIOS: Phonix 4.0 release 6.0 OS: REDHAT 9.0 I installed the X100P in PCI slot 2 and disable the USB port, serial-port and parallel-port in BIOS. I can't found the X100P card in " cat interrupts" But I can found the card in the "cat ioports" use "lspci" I found the X100Pcard use the interrupts 11 too. Who can help me to solve

Hi All, I hope I'm posting this to the appriopriate list, and that cross posting to two lists is OK. (If not, I'm sure I'll hear about it quickly :)) I'm running Asterisk on my (new) VIA EPIA-V motherboard. This seems to be the ideal platform for a home version of asterisk - its small, quiet, low power, and should have plenty of computing horsepower if only it would work!

Here's one last plea for help from the list before I give up on the totally cool software FAX modem concept in complete despair (for now, at least, until I have more time to dig into it).... I am simply not able to successfully receive a FAX no matter what device I transmit from or how I bring the call into Asterisk. My lastest effort was a call from a Pitney-Bowes FAX machine into an X100P

Dear Sirs, I'm running an Asterisk 0.9.1 in a Fedora Core 2 box. I installed a X100P card on my box and when i try to load modules i am rejected. When i type modprobe zaptel my Fedora respond : "FATAL: Module zaptel not found." . The same uccurs when i type "modprobe wcfxo" May you help me. Thank you in advance Juanjo

> Subject: Re: [Asterisk-Users] Booting error - Unable to specify channel 2: > No such device I just went through all this as well. The best thing to do IMHO is to try to find a way to manually assign IRQ in the BIOS. Also, and this is what I didn't see at first, some slots SHARE IRQ. Avoid this! If you are not using USB at all, turn it off in BIOS if possible. Tell the BIOS

Thanks for the reply Bill. I am aware of the interrupts problem. To solve it I have already disabled my serial ports freeing up interrupts 3 and 4 and these are allocated to the two cards. This was done 2 months ago and has not solved the problem. Is there any way that something can wake up every now and then and generate these two interrupts? My current /proc/interrupts is as follows:

Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o

We just had * crash on us - no calls could be made / received. We had to kill -9 the * process. Checking the error logs, I came across these two lines, with the times matching the crash: Aug 26 13:48:00 WARNING[19282] pbx.c: Local/6024@AgentQ-94ce,2 already has PBX structure?? Aug 26 13:48:00 WARNING[19282] channel.c: Thread -1105359952 Blocking 'Local/6024@AgentQ-94ce,2', already

Hi all, I am using a TDM400P card with 2 FXS and 2 FXO modules. Everything seems nice, but i'm not able to make calls nor to receive any. When I try to make a call, I keep receiven the "all circuits are busy now" message, and when I receive calls, asterisk doesn't seems to care (don't get anything on the CLI) I'm using Asterisk 1.2.17 and Zaptel 1.2.16 from Xorcom's

Hello all, I've posted on this problem before. Well here goes again. I have an intel mobo with a p4 2.4ghz proc, 1GB Ram. It has built-in ethernet and vga and 6 pci slots. I dreamed of making this my household communications server: internet router, firewall, vpn and asterisk. Everything works except the TDM fxs card. Well it works for a little while and it dies: no dialtone, no

I'm running a base demo install of Asterisk with ztdummy loaded on a 2Ghz Celeron with 256MB Ram - It's running on Fedora Core 2 in Text Only mode. I can connect with no issues but I'm getting intermitent popping and clicking noises in the demo playback - I've tried a variety of different codecs all with the same effect. It's the local wan so I can't see how QOS

Dear Jason, The code could look something like: dummyData = data.frame(Tract=seq(1, 10, by=1), ?? ?Pct = c(0.05,0.03,0.01,0.12,0.21,0.04,0.07,0.09,0.06,0.03), ?? ?Totpop = c(4000,3500,4500,4100,3900,4250,5100,4700,4950,4800)) # Define the cutoffs # - allow for duplicate entries; by = 0.03; # by = 0.01; cutoffs <- seq(0, 0.20, by = by) # Create a new column with cutoffs dummyData$Cutoff