similar to: Re: Asterisk-Users Digest, Vol 8, Issue 105

Hi, I'm trying to get a remote Cisco Call Manager Express (CME) system behind a dynamic IP address routing both inbound and outbound calls via SIP to my local asterisk server. I've got a local CME system working fine on the LAN, where the CME is at a static IP (host=10.5.7.130 in sip.conf), but I can't figure out how to get it working with host=dynamic, even locally on a test

hi: Just starting out with *, and I'm planning to heed the advice to start simple and small, but the goal i'm aiming for eventually is: *-based pbx for 10-20 seat small business, based in the UK. Users will have PoE SIP hardphones. So far so good, but two questions, both UK-specific, relating to connection to the outside world (PSTN or VoIP): - are there any UK-based VoIP providers

I sent this once already but it didnt show up in my mailbox so I am not sure if ever made it to the list. If it did, my apologies. I have an * system and an nbx. My plan is to use several grandstream 286s and plug the the phone cords into the NBX's analog FXO card. It works fine but after I make a call, the port stays open on the NBX and I cannot make another call for around five minutes

Hello, everyone, I am currently trying to get the asterisk server to talk with a 3COM NBX with T1 connection. My asterisk server has a T100p, TDM20B, a couple of sip phones. Now the sip phones are calling 3COM NBX phones fine, however, the analog phone has problem when dialing the NBX phones. The connection is established and the NBX auto-attendant picks up the call however the NBX end says that

Hi, I would like to simulate data with a binary outcome and a set of predictors that are correlated. I want to be able to fix the number of event (Y=1) vs. non-event (Y=0). Thus, I fix this and then simulate the predictors. I have 2 questions: 1. When the predictors are continuous, I can use mvrnorm(). However, if I have continuous, ordinal and binary predictors, I'm not sure how to simulate

Hi, I've looked pretty wide on Google for this so I don't think it's been asked before. Has anyone had experience integrating Asterisk with a 3COM NBX system? The only way that I can see that looks possible is via the 3Com NBX ConneXtions H.323 product and then one of the H.323 Asterisk channels. Has anyone done this? Any pointers as to what to avoid or whether to even attempt it?

We've been talking about moving from our NBX100 to an asterisk solution for some time now. Well, to make a long story short, the call processor on our NBX has went south. We are now forced to purchase a new call processor >$500 or move our solution to asterisk. (Which is up and running and have been tested with Grandstream Adapters.) My question: Is there anyone out there that

Hi, I'm having trouble getting asterisk to report MWI to a Cisco CCME. I record a message in mailbox 29, but the subsequent MWI notifications I see continue to report no messages waiting. Are they reporting for the wrong mailbox? Is there some other option I have to set or change? I'm running asterisk-1.4.22 Since the mailbox is in [home] in voicemail.conf, I've tried things like

Dear my friends... I am still new in CentOS. I use CentOS 5 for my new server with cpanel. I have installed the cpanel. The steps were: 1. cd /tmp 2. wget http://layer1.cpanel.net/latest 3. sh latest The installation show a message that the cpanel installation was completed. But I can not see the cpanel login form on my server, either: "http://WWW.MYWEBSERVER.COM:2082" or:

Has there been any luck getting the 3Com NBX series phones to work with Asterisk? Thanks! -Andrew

How hard is it to integrate * into an existing 3com NBX setup? -Tim -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20041004/bf01e3d9/attachment.htm

I am starting to work on a similar solution, but with full call manager rather than CME. I am going to use Asterisk to accept POTS calls through PCI FXO ports (winmodems) and then forward the calls through to call manager via SIP. I don't have my FXO cards yet (waiting for UPS man!!) but I have * talking to the CM through SIP just fine. I am testing with the Cisco softphone, connected as a

Does anybody know if the 3com NBX 100 phones will work with Asterisk? The phones require a boot image to be sent either through layer2 or layer3 before they will function properly after being powered on each time. Thanks.

i am just curious how many * systems are in the real world with more than one user. do you run a certain version? you dont update CVS do you? any admins running a system of over twenty? over fifty? over one-hundred? i deal with 3com and nec systems all day (i am cerified in the 3com nbx advanced network telephony, elite voice mail, CCNA, A+, nec ipk, and soon to be "asterisk school of

Wow, I think that was the first really potent flamewar we've had on llvmdev. Looking on the positive side, I think this shows that the llvm community is growing and drawing interest from new people with new perspectives. This is a good thing. I want to thank everyone who was courteous in their response. As others have said, it is really important to be polite and try to be

Has any advancement been made to get 3102 operational in either a SIP or H323 asterisk environment. A post back in time mentioned a downloader service. >From the posts and articles I have read, the NCP is acting like a bootp and tftp server which uploads the configuration to the phone?? Am I close? if so, where does one get the SIP image for he 3102 and 2102 phones? I had 8 donated, but they

On Mon, Dec 1, 2014 at 11:18 AM, Rowland Penny <rowlandpenny at googlemail.com> wrote: > > Yes it is used in production :-) > > Samba has changed a little bit since 2001 :-D > Yes, I know it has. My point was that I've been working with Samba for quite some time, so this is not all new to me. I've also been contributing to the SME Server project on this front for

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

hi, My question is may be a bit out of scope but I don't know where to turn, I have a 1760 with a ccme 24 user licences 1 bri card. I want to configure a bri card in a cisco 1760 on port 0/0, the card is new, seen by the router, show isdn status gives layer 1 desactived , layer not activated, what ever I do, no shutdown command / shutdown command, etc , the green OK light never turn on,

After failing to install on two different machines that were running Windows, I realized that one machine had a bad hard-drive, and the other bad memory. So I've collected the good parts into one machine and installed CentOS with SME. This was the fastest install of Linux I have every seen, 15 minutes done, configured, and running, web and email server. It is a very secure config, no GUI