similar to: Zaptel.conf and multiple T1 woes

Displaying 20 results from an estimated 4000 matches similar to: "Zaptel.conf and multiple T1 woes"

2004 Apr 15
2
TE405P + Adit 600 and FXO module - should this work?
Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much
2006 Apr 24
3
Channel Restart and Dropped calls
We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]
2004 May 13
2
Unable to play dialtone on channel xx (Zaptel TE405P)
Hello, I'm running * on a very basic configuration. I have a Wildcard TE405P with the first T1 connected to a PRI line and the remaining three to Adtran TA750 channel banks with FXS modules. I successfully configured everything to work with a couple of Swissvoice IP10S handsets (MGCP) and analog extensions connected to the channel banks. The problem I'm having is that when I pick up any
2005 Jul 08
3
McLeod Integrated T1 - no PRI?
Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the
2005 Jan 24
2
Wildcard TE405P and TDM400 - TDM not working
Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,
2005 Jun 21
5
Problem with Connecting PBX to Asterisk
We have an old Telrad 128KSU PBX to which I am trying to connect asterisk in the following manner: Current Setup: Telco-> T1->PBX Desired Setup: Telco-> T1-> Asterisk-> T1-> PBX. I am first trying to setup the Asterisk -> T1->PBX part without disturbing existing setup so I can get asterisk to forward calls to PBX and once that is done, I would try to move the telco
2009 Dec 28
2
Multiple Digium cards with one NFAS trunkgroup
Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it
2003 Nov 20
4
T1 / Channel Bank Configuration
I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |
2004 Jul 24
3
Help with T1 PRI Configuration
I'm ordering a PRI T1 for use with Asterisk and a Digium Wildcard TE405P. The provider is asking me a number of questions about how I want to configure the line. Here goes: 1. Dial Tone - No, Yes - Precise, Yes - SCC 2. Framing - SF, ESF 3. Line Coding - AMI, B8ZS 4. Signaling Type - Ground Start, E&M, Loop Start w/Ring, Loop Start w/o Ring 5. Pulse Mode - DTMF, MF 6. Outpulse Start -
2004 Dec 03
3
Two zaptel T1 cards: no clock from one
List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to
2004 Jul 18
1
TE405P
I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with
2007 Apr 19
2
3rd T1 of quad card won't change signaling
Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make
2005 Feb 25
1
Asterisk in front of Toshiba CTX
I have googled, and wiki'ed until blue. Is it possible to put T1---*----Toshiba CTX ? I have a TE405P, with one interface programmed for the T1, I am not sure how to program the 2nd port to mimick the T1 to the Toshiba. The Zapata.conf [channels] switchtype=national context=from-pstn signalling=pri_cpe usecallerid=asreceived echocancel=yes echocancelwhenbridged=no echotraining=400
2006 Apr 18
6
T1 to cross connect remote PBX and asterisk
Looking for someone with a successful experience similar to this; I have a need to cross connect a 3COM NBX PBX PRI interface to asterisk, but over a long distance. We do not need any IP connectivity and the solution requires G.711u audio so there is no benefit to using IP. Has anyone here successfully cross connected any PBX PRI interface expecting NI2 PRI signaling B8ZS/ESF with an
2003 May 29
3
T1-PRI deployment questions...
I am ordering T1-PRI service from local service provider and have a few questions. Is there framing and coding considerations (or is it all one standard), if so what is best? How are calls routed based on DIDs - are these just dtmf tones passed after the call is picked up and treated as normal exten=> definitions? John This e-mail was scanned and found clean by Monroe-Woodbury CSD
2006 Jan 13
2
zapata.conf for non pri T1?
Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my
2004 Jul 05
2
T1 configuration, getting help via IRC?
In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The
2007 Apr 24
1
TE412P (T1/E1+DSP) digium card cause server crash
Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX
2007 Jan 24
1
Getting confused on signalling mode Vs framing and encoding: T1 CAS
Hello, I'm trying to make my asterisk box to act as a telco, in order to reproduce a US environment in europe. Our telco provider is giving us those settings: ESF B8ZF Inbound = E&M Immediate Outbound sig =Wink Start Yield to Glare = Yes Those trunks are using CAS for signaling. I have tried many configs/combinations in zaptel.conf and zapata-channels.conf In zaptel.conf, when having
2005 Jan 22
1
te405P and german PMX
Hi all, i am stuck with the configuration of asterisk - modules are loaded ( zaptel and wct4xxp ) - i have zaptel.conf configure, output of ztcfg -vv --- snip -- rapid:~# ztcfg -vv Zaptel Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet