similar to: X100P with Analogue DDI Trunks

Hi, I suspected that I the analogue phone should have got a pass through signal when the power was off to the server, unfortunately it doesn't. I kept asking digium support about that but they didn't give me an answer. The problem is how do I identify whether the X100P is incompatibel with the network or faulty without possibly wasting another USD100??? Aaron On Sat, 2004-05-15, Eric

You should be able to get ISDN though. I think BT provide this anywhere. Otherwise your solution will be a Primary rate (ISDN30) with 8 channels. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Matt Sent: 07 June 2004 10:19 To: asterisk-users@lists.digium.com Subject: Re: RE: [Asterisk-Users] Multiple DDI &

Hi there Background: I want to add DDI and voicemail to users on an existing analogue pabx.. It does not support ISDN. I have 10 DDI numbers via IAX which I am having sent to my Asterisk box. I have 2 X100P cards connected to 2 analogue extension ports of my main legacy analogue pabx. I have set up voicemail for each of my DDI numbers, and when a call comes in for the person at pabx

Hi Does anybody if the X100P works in Switzerland? We can't get a line to PSTN. When I run zttool it shows me always a red alert. I can make and receive calls with an anlog phone plugged in the phone connector. I've compiled and configured the card according to the wiki. Everything seemed to be ok. Is there a way to debug this? Regards Reto

Hi, I recently decided to change my setup from AsteriskNow to plain-asterisk 1.4, which I wanted to set up and configure myself on a server running Debian Etch 64bit version. Hardware: Asrock motherboard, model 775Dual880-Pro, with a Celeron D running at 2.8GHz, 1GB memory, standard Nvidia GF4MX videocard, and one X100P clone card. Running the AsteriskNow, everything worked fine, except for

as my first project with *, i would like to replace our old neax2400(sds) with an * server. i've got an X100p and a TDM400 on hand already. for the CO lines, the X100p works ok with fxsks signaling though there are still strange things happening every now and again but more testing is on the way. my real big problem is the DID lines which our telcos call DDI lines; (incoming calls only) i

Hello all, does anybody have experiences with DDI on ISDN BRI? I would like to order DDI with 10 or 100 numbers from telco company, and use DDI numbers for direct calling SIP/H323 clients. But I don't know if Asterisk supports it, in archive I found only one answer about it, and I'm not sure. I am going to use it with isdn4linux card. Maybe DDI is called differently in other countries,

Hi all, I have a problem with my asterisk box and an X100P FXO card. I am able to place outgoing calls from my SIP phone (Cisco 7940) to any external number using my PSTN line, but when I call my PSTN line from my cell phone, the Cisco doesn't ring (and no message appears in the Asterisk CLI). Here are my config files: zaptel.conf fxsks=1 loadzone = be defaultzone = be

Hi Folks, Prior to upgrading my Zaptel sources everything was working fine. I have a X100P connected to my analogue line. The handset port of the X100P is connected to my desk phone's line 2 input. When the analogue line rings I see the CID on my line 2 but not from Asterisk on line 1 via the Cicso ATA. This used to work fine until I upgraded the sources. I get this when watching the

I have a potential customer who has an existing PBX with analogue FXS ports connected to phones. He wants to allow a single remote worker to be connected to one of the analogue extension ports using VOIP. I know I could do it using Asterisk with an X100P card, but that seems a bit overkill. Does anyone know of an analogue->VOIP adapter that has an FXO port in it instead of just an FXS port?

Hi everyone, I want to get multiple DDI's and hunting across those DDI's in case one of the lines is busy using analog phone lines. The system is for a large house so I want 3 x PSTN lines. 3 x DDI's and the ability for those DDI's to be presented across all three PSTN lines. BT say you can't have more than one DDI number associated with a PSTN line and that you can't

Hi, Has anyone got the X100P to work with an anlogue line in the Republic of Ireland? I have the X100P installed but zttool indicates a Red Alarm status on the card. It is on its own interrupt and I have tried different PCI slots but all to no avail. Are there any alternatives to the X100P that can work with asterisk and are likely to work in Ireland? Thanks, Aaron

Hi folks! I'm using an X100P (connected to my phone line) and an S100U, and when I calls out from the phone connected to the S100U it is a very bad sound quality, it "pops" and "jitters" a lot. But internal calls from for example a SIP client to the phone on the S100U sounds good. Calls from an SIP client to the outside world using the X100P also works good! My second

I have asterisk successfully dialing out using a X100P over a normal analogue PSTN line. But when I try to dial out over an analogue line that goes via a hardware PBX the call asterisk does not dial. Is there a configuration change I should make ? I am thinking of something like not wating for dial tone.

Hi, I've just added an X101P FXO card to my asterisk machine. The card is detected ok but zttool always shows it in a RED alarm state, which I understand means that it doesn't detect the line. I've connected the card via the line socket to my analogue line using the cable that came with the card (and have also tried other cables too) but I always get a RED alarm. I'm located in

Hi, I have an X100P which receives an analog line from another PBX. These are the relevant entries in extensions, PHONE1=Zap/1 [macro-extensions] exten => s,1,Dial(${ARG1},20) exten => s,2,Voicemail2(u${ARG2}) exten => s,102,Voicemail2(b${ARG2}) exten => s,103,Hangup [home] include=>tozap exten => 2201,1,Macro(extensions,${PHONE1},${PHONE1VM}) exten =>

Peter - 40 phones and only 3 PSTN trunks?. I would recommend at least 2 BRIs for this. If you have ISDN you can also get DDI to the extensions.I would strongly recommend abandoning the analogue PSTN lines and using ISDN. The setup pain you will go through will be significantly less, combined with better audio, more features (like DDI numbers!) and much more robust connections. You should look

Hi, I am the "IT guy" at a small startup based in UK. At the moment we have 3 analogue (PSTN) lines and we will be adding another 2 or 3 soon. Later on we should be changing to ISDN30. One of the partners mentioned getting an analogue PBX now, and when we move to ISDN, then get a digital PBX. I though of Asterisk. I have seen the website in the past and I know that it can do the job

Hi Everyone, I've been using Asterisk now for a few months for my small office (which is mostly just me while other guys are always on the road so we rely heavily on telephones) - I'm very excited with Asterisk as it can do everything I've ever wanted to do with a PBX. I'm having a problem with an S100U USB --> Telephone interface. I haven't actually made it work yet

I've just been doing some tests using the manager API to originate an outgoing call via a X100P and connect the call to an extension: Action: Originate Channel: Zap/1/01234567890 Context: local-extensions Exten: 6000 Priority: 1 I've noticed that extension is getting called as soon as the outgoing call has been placed, rather than when it is answered. Is the X100P capable of detecting