similar to: Dial out through Broadvoice

Hi, all. The asterisk setup is working fine, receiving calls via broadvoice "initially". ? When call comes in via broadvoice number, asterisk picks it up and routes correctly, as long as the call came in within ~2 min from the previous one. In other words, as long as a call comes in within ~2 min since the previous one, asterisk will answer the call. However, if the call comes in

I configured this once now I forgot what I did. Two Broadvoice accounts. Incoming is simple - just use the phone numbers. Outgoing: Dial out on a specific line and/or set up the groups and select the other "line" if the first one is busy? -- James Taylor MetroTel 3505 Summerihll Road Suite 11 Texarkana, Texas 75503 903-793-1956

Hello everyone, Well here is my initial posting to the list, and I will admit Asterisk is new to me. I just got everything running here a couple days ago, so still learning the ropes for sure. OK, here is my problem. Currently I have it setup talking to a couple Cisco IP phones, and some Xten softphones, this works great. I also got an account with FreeWorld Dialup using IAX2 and that

Hello, Have a weird problem when using asterisk (1.0.6). There are certain numbers I cannot dial when using asterisk with my broadvoice account. No problems with inbound. With outbound calls, I can call some numbers (for example broadvoice customer support number) and unsuccessfully with some. However, when I configure my account directly on x-lite, I dont see these outbound problems. Here is a

I just signed up for the BroadVoice service a few hours ago, but for the life of me I can't get any incoming voice. The incoming connection is fine as it rings my extension from outside, but I can't hear anyone talking. Outgoing voice is working fine though. I've been looking through the archives, but I haven't found a solution to the problem yet. I even tried another router

Suddenly my broadvoice will no longer register. It was working fine for over 1 month without a single problem, now I get a SIP registration timed out message. I called them, and I was told that they are experiencing problems, and they hoped to have it resolved ASAP. I called them at around 10 AM EST this morning. It's now 8:30 EST PM, and I still have not heard back, and the problem is not

you can not ping that address because ICMP is turned off. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com]On Behalf Of Deon Rodden Sent: Monday, July 26, 2004 2:22 PM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Broadvoice problems again Attn: James Greetings, C:\>ping 147.135.8.129 Pinging

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

I have configured asterisk with the AMP php configuration utility. I am able to make outgoing calls through broadvoice but incoming calls are sent to BV's Voicemail and never actually enter the IVR. When I show sip debug info through the asterisk prompt it actually reads the incoming call from BV but then issues a busy signal sending the call to BV's voicemail. I also modified

Hi all, I've been trying to use BroadVoice as a SIP service provider. They don't officially support * but are helpful when it comes to answering questions for setup parameters. They claim they have no firewalls or access lists that need to be set up so I can get access to their servers. However, something's still not quite right when I use the parameters. It looks like our Asterisk

Hello, I'm using Asterisk@Home. I'm still new to Asterisk, and trying to grasp it all. I'm wanting to do a simple setup of One SIP provider (Broadvoice) and 3 SIP Software Phones. I'm able to call the VoIP provided line fine and get dropped to the digital receptionist (or mailbox). However, when I try to send outbound calls I get "Error 503 Service Unavailable" and

All, I signed up for a broadvoice BYOD plan over the weekend (very excited about their offering) and after about an hour I had asterisk registered and was making in and out bound calls. However, the next day (without changing anything) I couldn't call in or out and haven't been able to get it going again. I can connect using a softphone (X-Lite) and make calls in and out

Hello, I have been researching Asterisk and have a few questions. Is it possible to allow users to only call certain area codes? Reason for this is that the plan from BroadVoice allows unlimited calling to certain countries. Any country outside of this plan would be charged on a per minute basis and I am trying to avoid that. Another question is if there is a way to distinguish a land line

Hi all, I am trying to configure my Asterisk PBX to connect to a broadvoice account. I want incoming calls to go to the "s" extension and to ultimately have outbound calls routed through my broadvoice account(s). I cannot for the life of me get this to register correctly. I am currently receiving this message on the console: Failed to authenticate on Register to

Egad, not again with Broadvoice! Anyhow, I recently installed AAH and configured my TDM11B and got that and some SIP phones working. I still have some issues to work out, etc, but my current problem is Broadvoice. I have checked out all of the online resources, including the recent list exchange about the recent changes made by Broadvoice. However, the one thing I have found to be consitent in

Is anyone else experiencing 404 errors on outbound dial with Broadvoice? I've followed the instructions posted by Broadvoice to configure sip.conf, and inbound calling works fine. Every time I try to dial out, I get a 404 "Not Found" error. Here are the relevant sections from my configs. sip.conf: context=broadvoice-in register =>

All, I have been fighting with my dialplan for hours now, and google searches talk lots but offer nothing in terms of explication for this. I have my SIP peer set up and working with Broadvoice: [sip.broadvoice.com] type=peer user=phone host=sip.broadvoice.com fromdomain=sip.broadvoice.com fromuser=5555551234 secret=password defaultuser=5555551234 insecure=port,invite context=broadvoice

Hello All, I'm just getting into *, and trying to use a Broadvoice account. It works inbound, but Outbound fails no matter what sip.conf parameters I try. From the recent posts here I think it could be: A bad CVS release - I will try to download and build from a new one Broadvoice not challenging and/or Asterisk not responding with an Authorization: in the INVITE header. I am

*sigh* Ok, I have fought and fought with this. I have read all the FAQ's, I have scanned the list archives. I can receive calls on * from my Broadvoice acct, but I cannot place calls... I have the 'World Unlimited' plan, and like 5 area codes that are local to me in Dallas. Can anyone help me? here are my config files... - sip.conf - [general] context=default ;

I'm getting a couple strange things with asterisk on Broadvoice. It works fine currently for inbound and outbound. Everything is registered, its perfect. My problems currently are: 1) After 20 minutes audio out to broadvoice goes away 2) After about 3 hours my registration attempts to broadvoice time out and the only solution is to switch to a different proxy which subsequently works.