similar to: Wildcard failing to load on asterisk@home

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Hello! I discovered, that I'm unable to load ther kernel module under 2.4.28. Before that I had 2.4.26 and tryed to upgrade the kernel to 2.4.28. After restart (reboot - soft restart) I can't load the module. When I go back to 2.4.26 and try to load the module, I'm getting the same problem. Only turning off/on helps. What can I do? It's very annoying because the box is in hosting

Hmm, I don't have /etc/modprobe.conf, and wctdm is giving me problems. Which device is it talking about? [root@asterix /]# modprobe wctdm /lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Hi all, I?ve ran into a problem regarding D-channels. I have setup Asterisk (CVS-HEAD-03/21/05-16:41:57) on RH Fedora Core 3(2.6.10-1.770_FC3) I also have a digium wcte11xp card for connetivity to the PSTN(E1). When I start zttool i see that Current Alarms changes between Recovering and Blue Alarm/Recovering. I started to see these problems after i moved the digiumcard from one PCI slot to

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Hi I'm trying to get a Digium TE110P card working but as soon as I load the module with modprobe wcte11xp the sound stops working for incoming calls (SIP and IAX). I haven't even started to configure the card. Running ztcfg and restarting asterisk doesn't help. After unloading with rmmod wcte11xp the sound comes back for new calls I'm using asterisk 1.2.4, libpri 1.2.2 and

This is a system for our lab. I have no problem getting rid of X100P clones. But I am just curious why can they work. Even the drivers are not loading correctly. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kerry Garrison Sent: Tuesday, May 02, 2006 10:51 AM To: 'Asterisk Users Mailing List -

Hi, I have problem using Asterisk.I have isdn-pri and openvox d110p card in my computer.They are connected with RJ-45 (1,2,4,5 pins to the card and all pins to the isdn done by telco workers). I got green led on isdn which is sign that isdn is working and that is connected to openvox, right ? I compiled newest versions of libpri zaptel and asterisk and had no problems during that. When I started

I'm running the latest firmware on the SPA-841 and have a problem with echo. The echo occurs on all calls (PRI ISDN on a E110p or SIP) and is not present when I use the SNOM190 phones so I can def. isolate it down to the SPA-841s. The codec used is g711u and the phones are on their own dedicated 100mbit switch with no other traffic. The server is a 3Ghz PIV sitting at 99.9% idle all

I am having problems loading the zaphfc from bristuff and wcte11xp drivers at the same time. If I load zaphfc then all works fine. If I then load wcte11xp, the card using the zaphfc doesn't pick up calls anymore. I am using bristuff 0.2.0-RC5. Anyone else seen this problem, know of a fix, or can tell me what I am doing wrong? Thanks My zaptel.conf: # hfc-s pci a span definition # most of

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi all, I am running asterisk 1.2.18, zaptel 1.2.18, libpri 1.2.4. on a suse 10.2, running kernel 2.6.18.2-34-default. The zaptel drivers are loaded on boot via /etc/init.d/zaptel, but Asterisk is unable to start. It ends with the following message: [chan_zap.so] => (Zapata Telephony w/PRI) Jun 13 13:05:41 VERBOSE[3356] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found

Hi, is it possible to set a wcte11xp card to use a certain IRQ? I've tried a few things but it always shares the IRQ with eth0 even though the system has 4 spare ones. I can't set it via the BIOS. Regards Lee -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050902/9ce217db/attachment.htm

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

Hello List, i am trying to set up an * box with a debian 2.6.10 Kernel. the compilation of asterisk and the zaptel drivers worked almost perfectly. so i did modprobe zaptel modprobe wcte11xp (which is the correct driver for my card) ztcfg -v and this results in ZT_SPANCONFIG failed on span 1: No such device or address (6) I don?t have any ideas whats wrong. google was no help, checking sources

Hi List, I am having some trouble with installing the latest version of ztdummy on a CentOS Kernel 2.6 system. I have installed a few Asterisk systems on Slackware Kernel 2.4.x without any issues, unfortunately there is no choice about this distro, or kernel as it has been preinstalled by someone else. And so I am in the dark with an unfamiliar distro and kernel. I am fairly sure the

Ok so I read the Linux 2.6 related README and finally compiled propperly, I thought but at the end I notice that lscpi does report the cards, but I cant modprobe wcfxo nor zaptel and I do have wcfxo.ko in the /lib/modules/2.6.8/extra/ directory, so what gives? This is a Debian Sarge, thanks! # # make clean starts here # make[1]: Entering directory `/usr/src/zaptel-1.4.0/menuselect' rm

Hi, I've compiled Asterisk cvs stable (few days ago) unde Suse 9.2 without any problems. We're using te110p and wcte11xp module that is autoloaded by Suse 9.2. Card goes green after reboot, but this meesages appear in logs: Mar 22 11:28:51 linux kernel: Zapata Telephony Interface Registered on major 196 Mar 22 11:28:51 linux modprobe: FATAL: Error inserting torisa

Hi, I plan to setup an * Server with a TE10P PRI card as E1 and a BN4S0 4 Port BRI card in one box. I tried it first with the bristuff drivers from Junghanns. The BRI card worked fine alone, but as soon as I load the zaptel driver for the TE110P the BRI card says, that the port is down. So I tried it with mISDN. But it seems that this stuff is still unstable (Asterisk refuses to start at first