similar to: Problem with ISDN Dialin via CAPI

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a

Hello, i have asterisk with chan_capi ( AVM Fritz card ) working, isdn line BRI, setup to point-to-multipoint. working fine, but when both channel on interfaces are used and somebody wants to call in - the response is "ha-la-li" - sounds like msn or called number does not exists. i think that right response should be - line busy tone... right ? can anybody tell me what is wrong ?

Hi, i was able to solve my problem. During my playing around with * and capi i changed several options in config files. I did this while my * was running. To test if my changes where successful i entered "reload" on * console. This didn't help. But after i stopped asterisk and startet it again, everything worked perfect. So it seems that doing a reload while asterisk is running

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hello everybody! happy new year ;-) I have a problem with inbound calls on my Diva Server PRI This is my problem: 2005-01-05 15:38:04 ERROR[31716]: chan_capi.c:1696 pipe_msg: did not find device for msn = 4132 capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 language=de [interfaces] msn=4132 incomingmsn=* controller=1 context=demo mode=immediate

Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and

Hi, I've a Fritz card which was working fine, recently I changed hardware and my nightmare started. Now when I call someone through the chan_capi (0.3.5 or 0.4.0) it works fine but when I receive calls I always get hungup. Can someone please give some help? Here are the logs: *CLI> -- CONNECT_IND ID=001 #0x0000 LEN=0049 Controller/PLCI/NCCI = 0x101 CIPValue

Hello, I need to detect both fax and answer machine, and it should be valuable that the detection will be run by the Diva card itself. So : - I read Diva Documentation, and I found that the Diva could send some specific DTMF, if I had "[..] enabled [this functionnality] by the application for a designated controller through a manufacturer request command 9 [...]", but I didn't

I have a Diva Server BRI installed in a Debian system running Asterisk 1.2.22. When a call comes in the Background application plays a couple of times. Halfway through the second time, the call is disconnected (total time connected about 25 seconds). I've posted various configs below. Any advice on how to debug would be appreciated. We are located in New Zealand. CLI showing capi debug (just

Good day, The unusual thing about this problem is that it doesn't occur just during a CAPI call, or just during an IAX/SIP call. Only during IAX/CAPI I'm having some trouble with the CAPI interface and it only occurs when a call comes in on an IAX channel and goes out the CAPI interface. The capi debug in the asterisk console is below as well as the relevent parts of .conf files from

Hi everybody, I have a problem which I cannot eliminate on my own. Has anybody any idea for the following: I am using the asterisk-version from Debian-Testing (1.2.13) with the latest chan_capi (also tried an older version). When using the Capi-Channel, everything works fine except from the sound it sounds extremely choppy and is unusable :-( When e.g. capisuite is used for fax, everything

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hi, I am having a problem with (Asterisk is crashing) with a Fritz card PCI / chan_capi. Receiving Calls from PSTN works, but outbound calls make asterisk crash (Speicherzugriffsfehler/Segmentation fault). The crash occurs upon dialing with the other phone not even ringing. I hereby ask if somebody reading this list can confirm or disprove my issue. Does anbody run a recent asterisk 2.6 with

Hi, I installed Asterisk with CAPI support. Everything works fine while starting Asterisk, but when a call comes in Asterisk hangsup the call after two times of ringing. The output is like: Jun 24 22:19:49 NOTICE[1082178480]: chan_capi.c:1931 capi_handle_msg: CONNECT_IND ID=002 #0x011d LEN=0048 Controller/PLCI/NCCI = 0x101 CIPValue = 0x10

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

hi, I've been running a pure sip asterisk box for a while now with no problems, and i've recently added an isdn2e line from bt in the uk. everything is hooked up and i've got it ringing my sip extensions, but the logs don't quite look perfect and i can't see any description of what i should consider to be normal behaviour. would someone be able to look this over and tell me

Hello All, I am having an odd problem with Armin's chan-capi_cm on builds higher than 7955. It would seem that this happens on anything higher than 7955. What is happening is the isdn is ringing, then asterisk does a goto-if and just hangs. Asterisk itself is ok, but the isdn then rings out or busys out on the other side. Outgoing works fine, this only seems to effect incoming. I

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/bmp Size: 2918 bytes Desc: Picture (Metafile) Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050307/cb404791/attachment.bmp