similar to: Time to beg on my knees for help!!!

Hi All, Channels 25-28 on a customers PBX are regular Zaptel FXO cards that are hooked into 4 incomming phone lines. They are all in a group to do automatic rollover for outgoing calls (if channel 25 is being used, dial on channel 26, etc.). Sometimes when a user is dialing a number, instead of bridging to one of the FXO cards it goes and rings to Zap/1-1. This doesnt occur all the time but some

Hello. I am a spanish student, so excuse my English. I have this HW: - 2 X100P PCI with two analog lines plugged in. These lines are two extensions of a panasonic PBX. Zap/1 = X100P <-- analog line --> extension #237 PBX Panasonic Zap/2 = X100P <-- analog line --> extension #245 PBX Panasonic - 1 TDM20B with two analog telephones plugged in. Zap/3 = TDM20B

See: http://lists.digium.com/pipermail/asterisk-users/2004-September/063348.h tml -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kumara Jayaweera Sent: Tuesday, June 14, 2005 1:46 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] RJ45 instead RJ11 in Digium's TDM20B card help meplease

I have a TDM20B and asterisk compiled fine. The drivers have been loaded (wcfxs and run ztcfg -vv, I see the drivers loaded with lsmod). Asterisk starts up fine. I am using the default configuration files that are made when you do a "make samples". I was wondering if someone had a link or website that stepped someone through this kind of setup. What I want to do right now, is use a

Dear all, I am happy to tell you that I received a Digium's TDM20B card for my Asterisk box today. but the phone jack is RJ45 instead of RJ11. So Please I need precise instructions to connect a phone to this card. please, assume that I have a phone (a normal analouge phone connected to the one end of a cable with an RJ11 jack (at the phone side). and now I want to connect the other end to the

All, Alright, I've looked around the internet, the voip-info.org wiki, and browsed the contents of this mailing list. While I've found a couple of scenarios that are close to this one, I haven't found one that uses my particular card (T100P). Without further delay -- I have successfully configured internal SIP services between a Snom 200 and a Windows X-Lite client and have

Hi all, I am going to have a TDM20B FXS card and sit in it in my Asterisk box, I need out going calls only. I am quite a newbei of it, I hope your tips and tricks with valuable links. Thank you Kumara

I am trying to find an example of how to set up my FXS Station Card in my Asterisk. I have (1) XP100P I have (1) tdm20B (2 Port FXS) Could someone tell me if this is correct? /etc/zaptel.conf fxsks=1 fxoks=2 fxoks=3 loadzone=us defaultzone=us /etc/asterisk/zapata.conf [channels] ; language=en ; ;X100P Port 1 context=inbound-analog signalling=fxs_ks usecallerid=yes echocancel=yes

Hi all, I have a vergin Linux box (FC3) and Digium's TDM20B card installed in it. I followed the Digium's quick intallation guide. donwloded CVS successfully, installed in this order zaptel>libpri>Asterisk and got this error without installing asterisk in my box. ***************************************************** (this is the end of the screen dump) /usr/bin/ld: cannot find -lidn

I have posted this to the Asterisk Forums, but got no response yet. Sorry if you are reading this for the second time. What fax hardware do I need for a T1? Ideally, I will switch my T1 to a digital PRI (not CAS I'm told, which is not as good) coming into the building. My CLEC said I can do this switch no problem. I have an analog T1 coming in now. >From the Asterisk box, I will connect

Hello, everyone, I am currently trying to get the asterisk server to talk with a 3COM NBX with T1 connection. My asterisk server has a T100p, TDM20B, a couple of sip phones. Now the sip phones are calling 3COM NBX phones fine, however, the analog phone has problem when dialing the NBX phones. The connection is established and the NBX auto-attendant picks up the call however the NBX end says that

Hello all, Been a while since I've strolled this way. Apologies in advance if this is a common line of questioning. I've just bought a new Intel 865G based board with a P4 Hyperthreading processor. I believe I've gotten SMP set up correctly: in the menuconfig I specified SMP and told acpi to enumerate processors. Did I leave out anything? Anyway, the dmesg looks good and the

Greetings! to all Now, with some hard time and help from many genurous people's in the list, I have come to this point with my TDM20B card & my teliax's IAX2 account. I hope someone may help me with this issue mentioned below. I have already selected my codec as gms in my iax.conf as well as in teliax's "my account page" but still i have the same error when I attempt

Hi I have been searching the wiki and mailing lists and I cant see where my config is incorrect. I have a Digium tdm11b (1 fxo + 1 fxs) this is the output of cat /etc/zaptel.conf # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order # Span 1: WCTDM/0

I have two x100p cards and a TDM20b set up such that the home phone is one exten, the home office is another, on one of the incoming lines (the same copper line that has the main home phone number) There is a distinctive ringing number set up as well. Here's the crazy part. any calls coming in on that line I want to ring both extensions. But I want the distinctive ringing to pass through only

Hi all, again, with another question ( may be the final one) I have come up to this point, means when I dial a number in my analogue (panasonic) phone I hear the ring at the end through my asterisk box (via TDM20B card) that uses IAX2 over teliax and after time-out, it gives this message. Starting simple switch on 'Zap/1-1' -- Executing

Hi All, I am very happy to say that after solving a lot of problems I got my Asterisk box talking (with a Digium's TDM20B card) last 48hrs I was sending message to many people asking help. I found some solutions myself but the base of those solutions given by the generous people in the list. I appriciate all of them once again. Now, I have minor problems like jitter and fine-tuning, I am going

Hi, I have a TDM21B (A new TDM20B that just arrived plus a X400M that I already had). This card sometimes works, and sometimes only the FXO module is seen. By "works", I mean all 3 modules have the green lights on the ports on and when zaptel is loaded the log shows: Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

I'm having problems with a TDM22B. The FXO modules work fine. Both FXS modules fail to initialized. The error messages I see when the module loads: Init Indirect Registers UNSUCCESSFULLY. Indirect Registers failed verification. I already RMA'ed a TDM22B because of this problem. Now that the replacement shows a similar issue, I want to see if anyone else can think of something to