similar to: Difference between a TE410P and TE405P?

http://www.mixdown.ca/~asterisk/ The card seems to be working fine. Don't expect warranty on it though. :-) Why? Because I wanted a quad-span T1 card which worked in the high-end systems I was intending it for, but that I could also keep a few in stock and if the system mainboard failed, pull the card an put it in a standard PC system. I didn't want to have to stock 3.3V and 5V

Is there anything to choose, in performance, between a TE405P and a TE410P? I understand the difference between the PCI bus voltages, and certainly don't intend to try Andrew's hacksaw operation :-). But if I choose the card first, and a compatible mobo second, does it make any difference which? Cheers Tony -- Tony Mountifield Work: tony@softins.co.uk - http://www.softins.co.uk Play:

I am getting ready to purchase my first Digium card to start experimenting with Asterisk. Before I make my purchase, I wanted to make sure I'm not going to have issues with these cards (need to see what the specs are on my box, 5V or 3.3V PCI ). I will be using Asterisk @ Home, so will be Asterisk v1.0.9. I took a quick poke at the lists, and it appears several people have been having

I'm having some trouble here - need some help! I've just bought a TE405p (32-bit 5V), but cannot get it working in a dell 6450. The dell has (from tech specs) "three peer PCI buses: two 64-bit buses and one 32-bit bus Expansion slots seven hot-pluggable PCI slots (two 64-bit/66 MHz, four 64-bit/33 MHz, and one 32-bit/33 MHz)" I cannot get the card working in any of the slots.

Hi all, I'm looking for a new system which will use the TE410P. Originally I was going to use a dual Athlon MP system, but my supplier tells me these are being phased out now, and so will be difficult to find replacement parts later. So, I am looking for suggestions of suitable motherboards with 3.3V PCI slots for the following CPU types (in order of my personal preference) AMD Opteron 1xx

hi, after stumbling over the compile time flag in zaptel and after reading the new features of the 2nd generation firmware of the TE405P/TE410P, i was wondering if the cards are capable of upgrading the firmware in field? regards frank

Anyone care to elaborate on the differences between the T400P and the TE405P? -Darren -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050908/e817f8bb/attachment.htm

Why PCI 3.3V for E1/T1 card!? I can not use it because I can not find any motherboard with PCI 3.3 . Any sugestions!? Cristian VASILIU AccessNET International S.A. Software Programmer mail to :<cvasiliu@accessnet.ro> www:<http://cvasiliu.home.ro>

lspci dont show Digium card. The motherboard is Intel 945gnt. 00:00.0 Host bridge: Intel Corporation 945G/P Memory Controller Hub (rev 02) 00:02.0 Display controller: Intel Corporation 945G Integrated Graphics Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev

Max TE410P card on an Asterisk Hello, Does anybody know the max number of TE410P/TE405P card we can put in an asterisk box? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040504/f220d3ae/attachment.htm

Has anyone else experienced a problem with the LED for span 1 on a TE410P or TE405P? I had a TE410P on which the span 1 LED would not light red, but once the span was connected, it did correctly light green. I RMAed the board to our UK distrbutor and received a replacement. However, the replacement board displayed the same problem! Wondering if it was related to the computer I was putting it

Hi, this is my 1st message, I'm writing to ask if anyone knows if a PCI32 card like the TDM400P (quad analog) or the B410P (quad BRI) is working on a PCI-X bus, at 100MHz or 133 MHz. I'm really stuck with this, since I found a partial "yes" on this mailing list but my supplier says "no"! Thanks, Marco

Hello, We have finished our tests of the new Digium firmware on the quad T1 cards(TE405P/TE410P). Overall it is a big improvement over the version 1 firmware. Here's the review: http://astguiclient.blogspot.com/2005/09/digium-405p-v2-review.html MATT--- -------------- next part -------------- An HTML attachment was scrubbed... URL:

I successfully installed asterisk@home 0.6, but when i try to load the wct4xxp module for the TE405P I just got, I get the following: Found TE410P at base address fb7ffc00, remapped to e0220c00 TE410P version c01a009b Tried to load 1c8ac800 into 00000000, but got 188ac800 instead Tried to load 1c8ac000 into 00000001, but got 188ac000 instead Tried to load 07fc07fc into 00000002, but got 03fc07fc

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

I am planning to buy Dell 2650 server with dual Xeon processors. And I would like to buy two TE410P cards for PCI with 3,3v. This is on Dell site about PCI slots for Dell 2650 server: 3 PCI-X (1x64-bit/133MHz, and 2x64-bit/100MHz) Does that mean I will be able to buy two TE410P cards ? Or I need to buy two TE405P cards ? Thanks for help. bartek

Hi all, Does somebody know how I have to setup my TE405P ? Is it correct my configuration below ? Otherwise, can somebody help me ? Thanks, Angel. zaptel.conf span=1,1,0,ccs,hdb3 span=2,0,1,ccs,hdb3 span=3,0,1,ccs,hdb3 span=4,0,1,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31

Hi, Is anyone here using the SuperMicro SuperServer 6014P-8R with Asterisk? I'm especially interested if you've used it with a TE405P or TE410P. Cheers Tony -- Tony Mountifield Work: tony@softins.co.uk - http://www.softins.co.uk Play: tony@mountifield.org - http://tony.mountifield.org

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Hi, I just bought the E100P from digium. It has both keys: 3.3V and 5V, so it would fit both, in a 5V-PCI slot and in a 3.3V PCI slot. Is it true, that I can plug it without destroying it in an ordenary 5V PCI slot? Roger.