similar to: Budgetone 101

Hi, I''ve a local LAN consisting of about 150 machines. I''m using a Linux machine as the gateway machine which inturn connects to two different ISPs. My question is can a Linux based machine match the performance of a hardware based routers provided by Cisco,... OR is my decision to go for a Linux based solution is a wrong one?. Is there so much difference between these

I'm using tftp server that automatically loads on each reboot, for some reason the last 2 files fail to load each time. (and I think this has always been the case) Aborted 192.168.16.32 C:\Program Files\TFTP Desktop\1.0.5.18\cfg000b82005c24 Octet, Send 192.168.16.20 25 Jan 18:25 Error Aborted 192.168.16.32 C:\Program Files\TFTP

Maybe I'm loosing my mind but I've just noticed that if I put a call on speakerphone and I press speakerphone again it hangs up the call, you would expect it to take the call off speaker back on to the hand piece. I'm using V 1.0.5.22 firmware. Is there any other way to turn off speakerphone I'm missing? Cheers, Dean -------------- next part -------------- An

I have several Linux machines some running on really old hardware and some on brand new, some run old distros (RedHat 6) and some new (FC3 or CentOS). All of them experienced power failure more then once, none of them has failed to load after a reboot. BUT, Asterisk is running your PBX. Your PBX isn't your proxy server, it isn't your web server, mail server, firewall, or whatever

I bought three plus two Grandstream BudgeTone 101 phones. The shipping cost more than the phone itself from Pulver store. The first shipping had one phone defect. Nothing on the display. (Can happen!) The second shipment had one phone with a defect display, but it still worked. The second phone's handset was defect too (microphone did not work). Changing the handset from this one to the

Hi Folks, Since there isn't a grandstream forum AFAIK I guess someone here may be able to shed some light on this. Apologies if this is viewed as offtopic.. I think I may have killed the firmware on my Grandstream Budgetone 101. I found a source for the 1.0.5.30 firmware and made the files available over tftp. The phone downloaded the files but now doesn't boot and hangs with a blank

Is anyone using this combination successfully? I have a dell 500sc running rh9 and asterisk 1.0rc1. It is configured with an x100p. I have a Sipura SPA-2000, laptop with Xlite and a Grandstream Budgetone BT-101. I have signed up with Voipjet (they use iax2). I also have an FWD number via iax2. I can sucessfully call back and forth to all devices via zap, sip, and fwd. I can successfully

Hi there, I'm having problems with the Grandstream Budgetone 101 on hangup - "show channels"/"show channels concise" output is still showing the call's channels as active. The problem does not exist when I use SJPhone, so I'm assuming it isn't an Asterisk configuration issue. Has anyone seen this, or better, does anyone have a fix? :) Thanks, David. --

I just got a Budgetone 101 and I have it hooked to my * box. I thought I'd read somewhere that we can program the buttons on these phones to send DTMF tones, thereby effectively programming them. However, according to the user's manual, they have predefined SIP functionality. My dialplan implements the festures I want (transfer, message, stuff like that), so for uniformity, I'd just

Hello, I am trying latest stable Firmware for GS IP Phone BudgeTone 101 found at http://gs-firmware.gratissip.dk/firmwares/ and the phone doesn't send a register staement (nothing in thertereal log). With the 1.0.3.81 version, the phone register properly. Is ther any know bug with the SW Version? Best regards, Daniel ANDRE -- Daniel ANDRE (mailto:daniel.andre@iris-tech.fr) IRIS

I am setting up a small Asterisk system for use at home. I have one Budgetone 101, one Cisco 7960 and two Xten lite softphones. So far everything is working expect for an issue with the Budgetone. When a call is placed between the Budgetone and any other phone, the call is setup and sounds good. If I hang-up on the Budgetone, everything is ok. If I hang up on the other phone, the Budgetone

Hello guys, I ask you to share your experience with your BudgeTone 100.... I have my asterisk @ work and I've bought a GrandStream BudgeTone (SIP phone) and I usually use X-Lite I have plugged my BudgeTone into my home network because I want to be called even at home. I succeed to register my X-Lite with Asterisk from home but I can't do that with my BudgeTone. (I don't know

Does anyone know what the Grandstream Budgetone is going for $$$ in the US? I didn't immediately see pricing on the phones page. AJ

I'm using 1 BudgeTone 100 IP Phone and a Sipura 2000 for all my old analog phones. The analog phones with the Sipura seem to work great. Voice quality is fine on both ends on the Sipura. I'm using the Teliax service and I use the Ulaw codec for all phones. However, I'm struggling with the BudgeTone 100. On my end, I find there is lot's of voice cut outs. I'm told my

I have the MusicOnHold feature working great when called from ATA-186 extensions. It's pretty cool. However, when I call from a BudgeTone-100 phone, no music is heard -- instead it continues the ringing feedback and acts like the call is unanswered. At the same time, I can call from (multiple) ATA-186 extensions and hear music as long as I like. How can I debug this? As far as I can tell,

Just for the record and to possibly help with others who get BudgeTone phones. My asterisk box is behind NAT, and I use Vonage, NuFone, and iconnecthere for my "POTS backhaul." On the front end I have an ATA186, a Digium TDM20, and now a BudgeTone 102. The BudgeTone definitely has issues wrt the RTP stream and NATting, although unfortunately I haven't yet been able to dig

Hi, I'm considering giving the Grandstream BudgeTone-102 phones a try. I've been using Cisco 7960's to date, but the low cost of the Grandstream phones are hard to ignore. I have two questions: 1) Does the message waiting indicator on the BudgeTone's work with Asterisk? 2) The one line 12-digit LDC concerns me a bit. Is the LCD able to display both the CID number and name on

Hello! I am considering mass deployment of Budgetones 102. According to their website, remote provisioning (configuration via TFTP) is possible. Anyone has experience with this? Is this really working?

Hi, Just playing with a couple of Budgetone 102 phones and they are pretty good for the price. The only problem i'm having at the moment is when I get a voicemail on the Asterisk box the LCD flashes. Dialing *98 goes to the VoiceMail Manager, and asks for mailbox, I enter 201, then asks for password, enter my voicemail password set in the Extensions -> webadmin, then hit the

I have a problem with using voicemail on the Budgetone phones. When entering the mailbox and password, sometimes some keys will register multiple times (as shown on console when it says no such user in config file) and sometimes some keys won't even register at all. It seems totally random. Has anyone seen this problem? Any recommendations would be greatly appreciated. Thanks. Brian