similar to: X100P DID

Thought I would post this experience to the list so it's archived for posterity... My company is deploying Asterisk-based PBX's to all of our branch offices. Each office has 2 analog Voice lines and a fax line. We didn't want to go to the expense of using TDM400's in the servers (which run asterisk and Hylafax) so we opted for 2 X100P cards in each box. So far they have

Hi, I just got two digium x100p clones and installed asterisk on fedora core 2 which took some tweaking. After getting asterisk up I installed the zaptel stuff - then modprobed zaptel, wcfxs (for the fxo cards), which worked fine. ztcfg is showing two channels configured, but when I start asterisk and do show channels, i see no active channels. zapata.conf has: signalling = fxs_ks

I have been experiencing hung up when answering incoming calls through x100p. NOTICE[1242768320]: chan_zap.c:4584 ss_thread: Got event 2 (ring/Answered).. -- Executing Wait("Zap/1-1","1") in new stack -- Executing Answer("Zap/1-1","") in new stack -- Executing DigitTimeout("Zap/1-1"."5") in new stack -- Set digit timeout to 5 --

I have an Asterisk server running todays CVS (updated it just in case that was the problem). It has 3 X100P cards. The first two lines I use as my normal work lines and the third is my fax line which I use with SpanDSP. I run Fedora Core 4. I have a problem that the third X100P does not answer the call. From the console I can see that there is an incoming call with the following: --

All of a sudden I am getting the following warning "Ring/off-hook in strange state 6 on channel1" from chan_zap.c and I cannot answer calls. I can place calls out without a problem though. Any ideas what can be the problem. I have checked zapata.conf and zaptel.conf and they both seem fine. Thanks in advance. Dan -------------- next part -------------- An HTML attachment was

Is there any way to make the X100P to check for a dialtone before dialing? My roommate is tired of hearing random dialing in his ear when he's on the phone (same circuit as the X100P). I know one solution is to just put in a TDM400P for the house, but I'd rather get away w/o having to do that. Thanks, Jared

Hi all, Really excited to be using Asterisk and learning about VOIP and PBX's. I'm a complete beginner at telephony but have built and installed Asterisk 1.4.5 and read several of the Asterisk books online and have successfully connected to FWD with IAX2 and to GIZMO using SIP. Just purchased a Motorola Wildcard X100P and installed it into a clone PC running Fedora Core 6. Analog

Does anyone know if there is a zapata.conf option to tell * to listen for a dialtone before dialing? I've got a couple of analog phones on a pstn line shared with a x100p * fx line. If someone is on the analog phone and another person initiates a call through * to use the same line, * dials over the top of the existing conversation. Is there a way to have * detect dialtone before dialing?

Hi A quicky - has anyone had success with an X100P in the UK ? I'm seeing some oddness - when I plug the wall socket into the card, I lose dialtone. If I unplug it, it comes back. Does this sound familiar to anyone ? Cheers Nigel Nigel Taylor Technology Director ITAzure Limited Dunn House Warren Park Way Enderby Leicestershire LE19 4SA 0116 286 3016

I have some strange behavior happening with call flow when analog line errors are encountered. This may be due to the way that the X100P detects "busy" signals, or it may be something in the software. Could someone with more in-depth knowledge make a comment on the items below? My dialing logic says "dial local area code numbers out of the analog line, and if the analog line

Hi, I suspected that I the analogue phone should have got a pass through signal when the power was off to the server, unfortunately it doesn't. I kept asking digium support about that but they didn't give me an answer. The problem is how do I identify whether the X100P is incompatibel with the network or faulty without possibly wasting another USD100??? Aaron On Sat, 2004-05-15, Eric

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

Hi, Has anyone got the X100P to work with an anlogue line in the Republic of Ireland? I have the X100P installed but zttool indicates a Red Alarm status on the card. It is on its own interrupt and I have tried different PCI slots but all to no avail. Are there any alternatives to the X100P that can work with asterisk and are likely to work in Ireland? Thanks, Aaron

I've configured an analog/single line off my mitel sx-2000 to a x100p card in my *, however when the remote caller drops the line I get a dialtone back from my pbx and the x100p doesn't detect the end of the call. Any way I can tell * to drop? I've tried call progress but it doesn't seem to work...

Hello, I have recently bought a X100P card. I installed asterisk succesfuly. When I plug my operator's line in the "line" jack of the card the result is that my line is not working any more. When I put it back to the phone, everything OK. It seems that the card leaves the line open! The same happens when I plug a telephone device in the "phone" jack. Furthermore, the

Hi All... I'm currently trying to have an extension of my Lucent Partner phone system connected to Asterisk using an X100P. The issue I'm having is that the Lucent Partner analog port connection have different ring and dialtone than the one specified for US in indications.conf. Anyone have accomplished this connection before. I need to know what I should use for the different

I have Asterisk setup in a SOHO environment. I have 2 X100P cards at Zap/1 and Zap/2. I have 1 TDM400P card with Zap/3 - Zap/5. I have subscribed to callwaiting, callerid and calleridcallwaiting from Qwest on the 2 PSTN lines - Zap/1 and Zap/2. My problem is when I'm in an active call to the outside thru Zap/1 or Zap/2, I can't pickup the incoming callwaiting call. I can see the

Hi, I recently decided to change my setup from AsteriskNow to plain-asterisk 1.4, which I wanted to set up and configure myself on a server running Debian Etch 64bit version. Hardware: Asrock motherboard, model 775Dual880-Pro, with a Celeron D running at 2.8GHz, 1GB memory, standard Nvidia GF4MX videocard, and one X100P clone card. Running the AsteriskNow, everything worked fine, except for

Hi. I have installed a x100p (THE x100p for those who have seen my former post). Now I just want to connect a "normal" phone (not an IP phone) to the card and use it as a sip extension (I have a FWD account)... more clearly: I want to be able to pick up the phone and call any FWD user using my FWD account... receive the FWD calls in that phone, and also to be able to make normal

Hello my brothers and sisters, Is "X100P" card suitable to VoIP? and if "yes", am i need to only "X100P" and "Asterisk" Package? or i need also to other cards or packages? and if "X100P" card not suitable to VoIP, please recommend a another card, (please take in your account that i would like to connect standard analog line to the card