similar to: TDM-400P alternatives?

Has anyone figured out how to power a Digium TDM 400P card in a Dell 1750 server? I opened the server and noticed that there is no access to 4 pin power to power the card. Is there some sort of adapter that I need to power the Digium card in a Dell Server? I see that the 1750 is listed on the Wiki. How have others powered the TDM400P in a Dell 1750?

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

I'm running a TDM-400P with 2 x FXS and 2 x FXO. I'm finding that there seems to be an odd relationship to sound quality on the card to my local when connecting via a SIP client. When I'm on my local network, if I connect to Asterisk via a SIP client (such as x-pro), and dial an outside line through the card, sound quality seems quite good. However, when I'm at a remote

A bit about my experience with the TDM-04 FXO. Only saw a few post on this subject, thought I would contribute a little about my experience to save others the hassle. a. As an earlier poster noted, the driver for the FXO is in the wcfxs module. Perhaps it should be renamed to something less confusing. b. You need the zaptel,zapata libraries from the cvs, the ones with Asterisk 0.7.2 won't

Hi all, I have a Digium TDM 400P at several locations. Once and again I'll need to restart the drivers because there is no ringing. Does anyone know a fix for this problem? Greatings Johan -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050906/66d9f13a/attachment.htm

Hi, I'm just starting out with Asterisk, in combination with a TDM400, filled with 2 FXS on channels 1 and 2, and 1 FXO on 4. Having just started, all I want right now is to be able to answer incoming calls on a phone connected to channel 1. The trouble is the caller id. I have caller id enabled on my line, my phone supports it, and when I connect the phone directly to the line, it works.

Hi: I am working on a new system with a TDM-400P card with three FXO modules and one FXS module. The system has been in place for a week. Users are complaining of echo problems. I have noticed this echo myself. It varies in severity. It is sometimes bad enough to make it difficult to converse, but the users find it generally unacceptable. They miss their old phones, which just worked. As you can

Hey, We are deploying an Asterisk machine in Malaysia for a client. The machine has a TDM400P with 2 x FXO & 2 x FXS. I'm wondering if there are any Malaysian users out there who might be able to help me out with a running zap config for their phone system. Cheers, Darryl.

Hi all, I'm trying to get a junghanns QuadBRI to coexist in the same machine as a Digium TDM400P card (so I can run the ISDN lines in and bridge with analog phones plugged into the TDM). I'm having a problem loading the modules. If I follow the BRIstuff (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod qozap.o I'm on Debian 2.4.31. That works. But then I

Hello all, I've posted on this problem before. Well here goes again. I have an intel mobo with a p4 2.4ghz proc, 1GB Ram. It has built-in ethernet and vga and 6 pci slots. I dreamed of making this my household communications server: internet router, firewall, vpn and asterisk. Everything works except the TDM fxs card. Well it works for a little while and it dies: no dialtone, no

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

Hi everybody, I have 3 TDM400P installed in a machine,and though the 4 ports of the first card work fine, some ports on the other two have low or no signal and a noise instead. Can someone help? Thanx __________________________________ Do you Yahoo!? Exclusive Video Premiere - Britney Spears http://launch.yahoo.com/promos/britneyspears/

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

Are there any cards that work with * that do the VoIP-to-TDM processing on the cards, with multiple interfaces? The QuickNet Internet LineJack meets the description I believe, but it only has a single FXS or FXO. Are there any cards that have more than one FXS? Thanks. __ Dana Olson Disclaimer: The information transmitted in this message is intended only for the person or entity to which it

Hello all. This is my very first message to the list. I have a TDM400P card, It has 2 FXO channels which are connected to extensions of my PBX (Ericsson BP250), so I can dial from any SIP softphone directly to physical (analog and digital) extensions on my company. My PBX is configured so when I dial 8 on any extension, it will redirect to the first free FXO channel on my TDM400P card.

Hi: I'm using a TDM-400 to terminate PSTN lines at my Asterisk server with kewlstart signalling. When an outside caller calls the server, the TDM-400 goes off-hook and provides a ringing tone to the caller. If the caller hangs up before the receiving party answers the phone, Asterisk fails to detect the hang-up. The TDM-400 stays off-hook, hogging the line, while Asterisk rings the

I've got a single TDM 400P board with two internal ports and 1 external. chan_dahdi.conf: context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks not auto Use FXO signalling for FXS group=0 channel => 1 ; Telephone attached to port 1 channel => 2 ; Telephone attached to port 2 context=incoming-pstn-line ; Incoming calls

In having configured my first * server there are a few questions I could not understand or find answers to 1) How does one use ztmonitor to adjust the rxgain and txgain. I have set mine to -1.0 each to get rid of echo on std phones connected on the TDM10B FXS module 2) Is it best to use a TDM card with an TFX and FXO module or is the the FXO = X100p and FXS on TDM a good method? 3) How do I

Would anyone care to offer opinions as to the FXO interface which sucks the least :) I have an application in which it appears I must route certain calls out an analog PSTN line. Presently, I am testing an SPA-3000, but I can't seem to get the echo heard on the IP end of the call down to a non-annoying level. Any suggestions welcomed :) -Dorn

It is a cable 4-5 meters long that has handssets connected I don't think its a matter of a distance __________________________________ Do you Yahoo!? Exclusive Video Premiere - Britney Spears http://launch.yahoo.com/promos/britneyspears/