similar to: wcte11xp Trouble

Hi all, I am running asterisk 1.2.18, zaptel 1.2.18, libpri 1.2.4. on a suse 10.2, running kernel 2.6.18.2-34-default. The zaptel drivers are loaded on boot via /etc/init.d/zaptel, but Asterisk is unable to start. It ends with the following message: [chan_zap.so] => (Zapata Telephony w/PRI) Jun 13 13:05:41 VERBOSE[3356] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

Hi there my zaptel hardware is giving errors while loading but they seem to load just fine. the lights wil work and my wctdm card is also workin and the isdn works to But when I stop asterisk I have to reload al cards again is this normal? This is my zaptel.conf is there no way to group these because my te110p is giving an error that it can't find channel 35 but 35 belongs to my wctdm.

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

We're rolling out Cisco 7940 phones, linked to *, which is running a TE405p EuroISDN. We have 2 ISDN lines, one we had for testing, and one for general (40+ users) use. During the testing phase, we had 10 phones linked to the second ISDN line, and there were no problems with echo at all. Lucky me. However, since we have started rolling out, we've had quite loud complaints that there is

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Hi steve and All, I'm attaching cat proc/interrupts out put, lspci -bv out put, zapa.conf, zaptel.conf for your information Thanks so much for the feedback and I do accordingly. Hope to get rid off this isue any how. To day also reported 10 call drops within 2 hours of period. fook forward to have your support on this regard. Thanks & Regards, Vidura Senadeera, Network Engineer,

I'm trying to load ztdummy on my Asterisk, running in a XEN domain. I've modified the code to disable the use of an RTC. I can load the zaptel module just fine, the ztdummy also loads without problem. But when running ztcfg I get this error. ----- s n i p ----- graham:~# ztcfg -vvvv Zaptel Version: 1.4.6 Echo Canceller: MG2 Configuration ====================== SPAN 1: CCS/ AMI

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

Hi, I have been using asterisk for a couple of months now and for thee most part, I love it. However, I'm having a problem with the drivers of the Digium TE110P. I have tried both the Debian package and the CVS. I have tried several kernels, and am now at 2.6.11. This has been working before (with 2.6.8.1), but after a reboot it stopped working and I am not able to consistently make

hello all, i'm using TE110P and all configuration prosess is done. but after i do the 'modprobe' for zaptel and wcte11xp, follow by ztcfg -vv and asterisk -vvvgc i have this error. *CLI> May 27 14:44:33 WARNING[3059]: chan_zap.c:8534 pri_dchannel: PRI Error: We think we're the network, but they think they're the network, too. May 27 14:44:34 WARNING[3059]: chan_zap.c:8534

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Hi All, I have installed a Digium TE110P card on an Asterisk 1.2.1 system. Its connected directly to the PSTN. But I am unable to make outbound calls on the zap channels. The light on the card is green. Asterisk CLI shows all 24 channels when I give the command 'zap show channels'. I also noticed that Asterisk CLI shows an incoming call every few seconds on the 24th channel. This must be

Im trying to install and configure sangoma ... every thing is OK but when type the command "wanrouter start" the following error apears: wan Driver not found. Thanks for any help

hello, i have a problem starting asterisk with one x100p digium and two hfc chipset isdn cards with bri-stuff.0.0.2. "ztcfg -vv" shows me a this info: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02) Channel 03:

Hi, I have this error, I have a digium card TE110P Tiger3xx When I'm load the dirvers by this command modprobe wcte11xp I got this error "Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for wct1xxp " when I'm Lunch the command ztcfg -vv I got this error.