similar to: OT: FWD and IAX: down?

I have set up FWD via IAX service. I have tested the IAX service with 613, echo test, and 612, saytime. It all works well. However when ringing a FWD user, I got this error all the time: Connected to Asterisk CVS-v1-0-02/01/05-09:34:45 currently running on chat (pid = 8282) chat*CLI> Verbosity is at least 3 -- Executing SetCallerID("SIP/1001-a1fb", ""David

I have configured iax.conf and extensions.conf as instructed on FWD website (http://www.freeworlddialup.com/help/?p=knowledgebase&c=18&a=76) and I can successfully receive calls and make test calls to 612, 613, etc. The problem is that I can not make a call to another FWD user. Here is what asterisk says: -- Executing [393xxxxxx@default:1] Set("Zap/1-1",

Hi, im trying to setup ASTCC but I'm getting it difficult. I've correctly set up the mysql database astcc and added a brand, trunk, route and a card as follows: brands +------+----------+------+--------------+------+--------+------+------+ | name | language | inc | publishednum | did | markup | days | fee | +------+----------+------+--------------+------+--------+------+------+ | FWD

I have looked all over the site(s) for help. But heres the problem. Im missing something. In coming works fine from FreeWorld via IAX. But when Dialing out i get: May 13 13:42:01 WARNING[1150495040]: chan_iax2.c:5256 socket_read: I don't know how to authenticate iaxtel to 65.39.205.121 my IAX.conf if as follows [general] port=5036 register => ######:xxxxxxxxxxxxx@iax2.fwdnet.net

Hello all, Here is my problem, I try to place a call to FWD (free world dialup) trough my asterisk PBX. my config is as follow: extensions.conf ---------------- [internal] exten => 613,1,Dial(IAX2/iaxfwd-outbound/613) (service echo de FWD) exten => xxxxxx,1,Dial(IAX2/iaxfwd-outbound/xxxxxx) mon numero FWD exten => yyyyyy,1,Dial(IAX2/iaxfwd-outbound/yyyyyy) celui d'un ami FWD

Hi, I got my * working fine with FWD at office with 2 extensions, i receive calls and i can make calls thru FWD. I got also my * at home, and i connected it using auth=rsa. From my home, i can make calls using my office iax, but if i try to redirect incomming calls from FWD to my * at home, it rejects the call. I created the pub/key pairs for rsa and its working ok and i just pasted the

When somebody call me on my pstn # cable connected to my fxo card it does not work when I check my computer the following error shows Connected to Asterisk CVS-v1-0-12/05/04-19:46:25 currently running on asterisk1 (pid = 2160) Verbosity is atleast 3 -- Remote UNIX connection -- Starting simple switch on 'Zap/1-1' == Starting Zap/1-1 at incoming,s,1 failed so falling

Im trying to get IAX to work between my * and FWD. I activated my iax2 account on iax.fwdnet.net and I get the output: "Registered to '65.39.205.121', who sees us as 68.14.203.254:4569" when I start asterisk. I tried used the Call Me tool on fwdnet.net but I dont get any calls even though the Call Me tool says everything looks ok. Can someone call my FWD number and just leave

I am having trouble with this. I can dial 1800 numbers fine as well as FWD service numbers but not Vonage. I can be called from ipkall and fwd and can call aixtel numbers. I use aix2 with Fwd. My extensions.conf for Vonage: ; vonage numbers ; ; +2431 exten => _2431XXXXXXXXXX,1,SetCallerID,${FWDCIDNAME} exten =>

Hello, I am trying to setup my Asterisk box to accept calls from the FWD network. I've followed all the config advice / samples I've found on the web. Making calls to devices on the FWD network from my Asterisk box works flawlessly, but whenever I try to call my Asterisk box from a FWD client I get a busy signal, and a "Call Disconnected" 486 error. What's odd is that I

I've setup my IAX2 over FWD and it is working I can receive a test call and I can call out. Though I cannot figure out how to dial 1-800 numbers over FWD When I dial 1-800 it hangs up on me. Here is a typical session: Called xxxxx:xxxxxxx@iax2.fwdnet.net/18007425877 -- Call accepted by 65.39.205.121 (format ULAW) -- Format for call is ULAW -- Hungup

Hi, I have an FWD account and it's configured in asterisk. I can be called by people using FWD, but I cannot make FWD calls myself. Every number dialed with a 8 prefix goes to FWD, if for example I call the echo servie I get this: Connected to Asterisk 1.2.13 currently running on asterisk (pid = 2865) Verbosity is at least 35 -- Executing SetCallerID("SIP/timothy-08224f08",

Sorry about this, I have been struggling with the basics of my asterisk config. I set up two sip peers and two phones. And I set up lots of dial masks for outgoing calls, all my outgoing calls were working great, however incoming calls were a different matter altogether, I cannot get incoming calls to work. So I have gone back to a very basic FWD config, with one phone which as far as I am aware

I'm trying to test IAX2 with FWD It registers fine but when I try to receive the call I get: chan_iax2.c:476 iax_error_output: Ignoring unknown information element 'Unknown IE' (38) of length 1 Jan 25 18:02:12 WARNING[114696]: chan_iax2.c:476 iax_error_output: Ignoring unknown information element 'Unknown IE' (39) of length 1 Jan 25 18:02:12 WARNING[114696]: chan_iax2.c:476

When I try to call out to FWD over IAX2 I get: Call rejected by 65.39.205.121: Unable to negotiate codec I'm using asterisk-1.0.5 (the same settings works fine with *0.9) I've standard settings in iax.conf [general] bindport=4569 register => xxxxx:xxxxxx@iax2.fwdnet.net [iaxfwd] type=user context=fromiaxfwd auth=rsa inkeys=freeworlddialup disallow=all allow=ulaw -- #Joseph

Hi, I'm slowly getting to grips with *. My next quest is to get IAX2/FWD calls working. I've setup a fwd account and added IAX capability to it via the website. I got the email saying it had been done with some welcome text and sample phone numbers to try, such as 10001 for the answer phone. I followed the setup example on the fwd site for configuring * to work with fwd's IAX.

When I use DISA I get congestion when I try to reach 1-800-number: Here is the context: [disa] exten => 087,1,Answer exten => 087,2,DigitTimeout,8 exten => 087,3,ResponseTimeout,20 exten => 087,4,Authenticate(985) exten => 087,5,DISA(951|disa-access) [disa-access] include => tollfree include => outgoing-voipjet [tollfree] ; ; terminate toll-free no.'s via fwdnet ; US

Hi, Soory, if I missed relevant help pages. I have developed several packages myself and want to give them to a collegue in *.tar.gz form (Unix, Solaris). What is the proper function to install them? install.packages() with a path pointing to the local temp instead of to CRAN? Thanks for help. Christian -- Dr.sc.math.Christian W. Hoffmann, http://www.wsl.ch/staff/christian.hoffmann

Hello, R-devel seems to be the appropriated list for what I'm to ask: soory if I'm wrong. I am a c newbie but nevertheless I am trying to 'couple' an extern c software with R. The compiled library is actually a stand-alone c program, which uses text file for input and output. It uses *lots* of differents and (to me) rather complicated and nested "struct"s to represent

Hi, I am performing a repeated measures 2-way ANOVA to assess the influence of plant and leaf on aphid fecundity. Fecundity is measured for each aphid on a single leaf. Here is what I typed. wingless <- reshape(Wingless, varying =