similar to: Getting a Wildcard TE110P working on E1's in Australia

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

Hello - I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I am not able to call the FXS extensions or get dialtone on them. The channel bank is connected via a T1 crossover to the cable and lights show green. I really need to get this functioning by end of day. If anyone can help me out I would be greatly appreciative. Thanks, Dave zaptel.conf loadzone =

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

About every hour I see the yellow alarms on all or a number of channels of my PRI which is connected to the dutch telephony network, Asterisk keeps on working fine.... Here's an example where channel 1-24 went into alarm: WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected alarm on channel 1: Yellow Alarm WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):

Hello Approximately every 15 minutes I'm getting the following error (on all channels): [Apr 7 01:34:27] WARNING[6530]: chan_zap.c:6628 handle_init_event: Detected alarm on channel 31: Yellow Alarm [Apr 7 01:34:27] WARNING[6529]: chan_zap.c:2388 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! [Apr 7 01:34:27] == Primary D-Channel on span 1 up

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi. I'm getting the following error at random intervals on my TE410P with Asterisk CVS-03/30/04-11:49:01-CEST. I have two spans active, one connected to my Telco, the other to a Siemens PABX. Both spans display this behavior at random intervals. All calls are dropped when this happens. Spans are not necessarily in use when this happens.

Hi guys, I've been trying to get my ISDN-10 line up for the past few days, but its been going up and down. I am using OpenVox D110P card on asterisk version 1.4.21. It seems to me like a cable problem. I tried using Ethernet straight cable (12, 45, 36, 78) and also a "straight" cable where the twisted pairs are on 12, 34, 56 and 78. The problem remains the same.

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Guys.. I just saw this for the first time... I did some google and wiki without any luck.. what does a red or yellow alarm mean in zaptel? Feb 23 02:54:16 WARNING[16890]: chan_zap.c:5865 handle_init_event: Detected alarm on channel 2: Red Alarm Feb 23 02:54:24 NOTICE[16890]: chan_zap.c:5860 handle_init_event: Alarm cleared on channel 2 This just happened by itself..

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

I have configured TDMoE sucessfully and I am able to make a Zap connection from one box to the other. The question I have is.. I'm getting repeated errors every second on both systems.. Oct 3 09:53:16 WARNING[4409]: chan_zap.c:6252 handle_init_event: Detected alarm on channel 1: No Alarm Oct 3 09:53:16 WARNING[4409]: chan_zap.c:6252 handle_init_event: Detected alarm on channel 2: No Alarm

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Good day eveyone, I'm hoping that someone can help me. Perhapps i'm overlooking the obvious, in truth, I hope that I am. I've scoured the mailing list and google, and haven't come up with much. I have a Digium T400P thats been connected to a channel bank for testing for some time now. all has been well. I've now just had

I need your help I have a sangoma A104D on my dell server; I got card status ok with no alarm If I dialed the extension 6210006, it shows the output as stated below, but there is no ringing from the pstn number nor the iax softphone am using on my pc. I will be glad if someone can give me a working config? What I want to achieve is to send all my call to the pstn on A104D? The pstn am

Hi, After temporarily pulling the T1 cable out of our Asterisk box, we ended up getting a strange error messages even after the cable was plugged back in. [...] Dec 10 09:01:11 WARNING[1192437440]: File chan_zap.c, Line 5683 (zt_pri_error): PRI: Read on 63 failed: Unknown error 500 Dec 10 09:01:21 WARNING[1192437440]: File chan_zap.c, Line 5683 (zt_pri_error): PRI: Read on 63 failed: Unknown

Hello, I'm trying to get a Wildcard T100P working with Asterisk and so far I haven't had any luck. No problems with the card itself from what I can see and the telco says that the problem is on our end (don't they always?). A small sample of what asterisk spews out on the console: Jan 13 15:45:32 WARNING[180236]: chan_zap.c:5834 zt_pri_error: PRI: Read on 43 failed: Unknown

Hi, we have a E1 pri from Citylink, (they are using Ericsson Engine exchange), that are restarting after 5 - 15 minutes, before and after that we can make calls in and out w/o problems. The cards have been tested in two computers (Atholon XP 2200+ and Celeron 2.6Ghz), are on there own IRQ, not showing any IRQ misses in zttool. It's all correctly configuered - zaptel and zapata (attached). We

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their