Displaying 20 results from an estimated 9000 matches similar to: "zaprtc from bristuff? not there?"
2005 Jan 25
3
Bristuff ZapHFC and Loosing D-Channel
Using the latest(?) bristuff (Asterisk 1.0.4-BRIstuffed-0.2.0-RC3a) I
have problems with loosing the D-channel. Most of the time, after the
message
"PRI D-channel down"
it only takes a second or so to come back up, noted by the message
"PRI D-channel up"
However, today most of the time the D-channel stays down. Calls come in,
but can't be answered.
Does anyone know
2005 Aug 15
1
bristuff-0.2.0-RC8n problems and kernel panic
Hi list!
On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n.
Everything did compile but I am running into some problems with the zaphfc
driver.
First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do
that) I get a kernel panic and the box hangs. Not so nice, especially when
you are trying to fix stuff from remote locations. But ok.
Now for
2005 Aug 04
1
bristuff-0.2.0RC8m
Hi,
I have following problems compiling bristuff-0.2.0RC8m. Has anybody seen
them before and can point me in the right direction?
zaphfc/make all:
----------------------
/usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c: In function
'hfc_findCards':
/usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c:1000: error:
invalid lvalue in assignment
make[2]: *** [
2005 Jun 27
0
bristuff-0.2.0-RC8h does not compile
Hi,
it helps to have configured and working kernel sources installed.
Configure your kernel sources for the running kernel and then run
"make" in the kernel source dir to build the necessary scripts.
You dont have to wait until the kernel is compiled.
best regards
Klaus
--
Klaus-Peter Junghanns
Am Samstag, den 25.06.2005, 02:45 +0200 schrieb Stefan Gofferje:
> Hi folks,
>
>
2005 Jan 22
1
zaprtc load issue (different that other postings)
zaprtc 'load' is failing on my machine (the make was fine, same output
as other posts to this list)
[xxx@xxx zaptelrtc]# make load
sync
modprobe zaptel
insmod ./zaprtc.o
./zaprtc.o: init_module: Input/output error
Hint: insmod errors can be caused by incorrect module parameters,
including invalid IO or IRQ parameters.
You may find more information in syslog or
2005 Aug 16
2
florz patch for bristuff breaks compile on x86_64?
After upgrading a CentOS 3.x box to CentOS 4.1 (both x86_64 with an
Athlon64) I also wanted to get the latest bristuff. Unfortunately
bristuff without florz causes the box to kernel panic within hours
(console will complain about bad frame received something).
It seems however that the florz patch will not work for x86_64 arch.
Bristuff -0.2.0-RC8j compiles fine without the florz patch, but
2005 Jul 17
2
HFC BRIstuff woes
Hi All,
It's broken !! (drat)
Asterisk if failing to load with the following error (taken from end of
/var/log/asterisk/full) after adding bristuff.
Can anyone help please?
Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone'
(Standard Linux Telephony API Driver)
Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54
VERBOSE[2503]: [chan_zap.so] =>
2005 Sep 23
1
zaphfc problem: overlapdial don't work after update bristuff
hello,
I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a
Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and
zaphfc driver - point2point mode -.
---------
| TELCO |
| BRI |
---------
|
| PBX external S0
--------
| PBX |
--------
| PBX internal P2P S0 NT Mode
|
| HFC-S Card P2P TE Mode
2005 May 18
6
zaphfc troubles
Hi,
I'm trying to setup a small BRI ISDN <-> voip gateway.
The ISDN card is based on Cologne chipset, so I try set it up with zaphfc.
The versions i'm running:
kernel-2.4.27
Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e
zaptel modules 1.0.7
zaphfc is from bristuff-0.2.0-RC8e
When I'm doing the insmod on zaptel, zaphfc, zaprtc:
Zapata Telephony Interface Registered on major 196
PCI:
2005 Mar 28
0
bristuff-0.2.0-RC7k: error on loading qozap : "qozap: Unknown symbol zt_xxxxx"
Hi,
I had problems described in another thread so went from a start, but now
have problems when loading qozap module. I get :
# insmod qozap.ko ports=9
insmod: error inserting 'qozap.ko': -1 Unknown symbol in module
and in /var/log/messages:
module qozap unsupported by SUSE/Novell, tainting kernel.
qozap: disagrees about version of symbol zt_receive
qozap: Unknown symbol zt_receive
2005 Jan 20
0
Poor sound quality on ISDN BRI calls
I've been struggling with connection Asterisk to ISDN BRI lines for a
while.
I have it working with the latest bristuff and compatible Asterisk
version:
Asterisk 1.0.3-BRIstuffed-0.2.0-RC3a
I am using a cheap Centronics ISDN card and the zaphfc drivers.
It works but users complain that the sound quality is not good.
They have Xlite phones on their desktops.
Xlite to Xlite through
2003 Dec 18
2
Zaprtc compile error - virtual device for conferencing
Hi,
I don't have a zaptel device for conferencing.
I read from the lists, that
ztdummy and zaprtc need to be installed to get conferencing.
I could able to compile successfully with ztdummy and when i receive the
call it says,
-- Goto (13732,s,1)
-- Executing MeetMe("SIP/-08118800", "1234") in new stack
== Parsing
2006 Jun 19
3
Bristuff-0.3.0-PRE-1q and & florz patch compile trouble
Again trouble compiling bristuff-0.3.0-PRE-1q with the florz patch on a
x86_64 box (I guess nobody is using x86_64 platform or is able to fix this
themselves?)
First of all when bristuff is downloaded and compile is started it appears
that the bristuff Makefiles are badly broken.
The asterisk Makefiles all do see to find the kernel sources on a RHEL4
box in the proper directory, the pure
2005 Jan 09
1
Can zaphfc (bristuff) do caller id?
Caller id is not in the configs that are supplied with zaphfc from
bristuff, and it's not mentioned in the wiki.
Is it possible to use callerid with zaphfc/bristuff?
Thanks!!
2006 Jan 05
1
bristuff/zaphfc disturbing other ISDN phones
I have ISDN BRI line (Point-to-multipoint), with HFC card and
bristuff/zaphfc driver.
I also have TA attached to NT, with analog phones and modem on it.
When I'm dialling through Asterisk/bristuff, and in the same time TA
have some conversation (or maybe modem link) on channel 1, I can hear
that conversation (or modem) very short period (0.2sec), and I also
disturbing that conversation
2005 Mar 04
1
Bristuff e RealTime: STABLE vs. CVS-HEAD
Hi all!
Was anybody able to install kapejod's zaphfc drivers together with RealTime
application? I'm in big trouble because bristuff relay on STABLE version,
while RealTime is included in the CVS-HEAD.
I found this hint, "Installing zaphfc with CVS-Head" at
http://voip-info.org/wiki-Asterisk+zaphfc+install, but it was written many
months ago: may it be still useful?
TIA,
Alex
2005 May 31
1
rxfax application - doesn't work properly
hi,
I am on fax-to-email system, basically taken from
http://www.voip-info.org/wiki-Asterisk+Fax+to+email
well, it seems that asterisk causes some problems so that it is impossible
to send any fax.
I.e. when I try to send a fax to asterisk (rxfax application):
normalFax--->FXS(TDM400P)--->Asterisk(RxFax) it breakes up the trasmission
at the beginning of sending page.
The code given by
2005 Feb 13
1
bad sound ISDN bristuff
Hello * users
I've problems with sound quality on zaphfc
Asterisk works fine good sound quality.
If I do "make load" in the bristuf.xx zaphfc dir then sound quality
drops directly.
Even if I don't load the chan_zap in the modules.conf
I use this config on more (even old 400Mhz machines) and works correctly.
Looks like an hardware problem but I can't find it.
I don't
2006 Jan 04
1
local exchange dialtone on ISDN/bristuff?
How can I get external (telecom local exchange) dialtone on HFC ISDN BRI
with bristuff/zaphfc driver?
with capi, voip-info say that it should be something like:
Dial(CAPI/MSN:b)
But with zaphfc, if I try: Dial(ZAP/1/), I just get NOANSWER.
2004 May 25
1
D-Channel on span 1 up/down + frame slips with zaptelBRI
I have installed two HFC PCI A-cards running zaphfc from bristuff-0.0.2,
which seems to work quite fine, but I continously receive the messages
"D-Channel on span 1 up" followed by "D-Channel on span 1 down" with a few
seconds interval. Why is that? Bri intense debug log and configuration
files below.
I don't need ztdummy or zaprtc, do I? I get some frame slips as well,