similar to: SPA-2000

> Message: 1 > Date: Fri, 21 Jan 2005 17:38:27 -0600 > From: "Henry Devito" <hdevito@qwest.net> > Subject: [Asterisk-Users] SPA-2000 > To: "Asterisk Users Mailing List - Non-Commercial Discussion" > <asterisk-users@lists.digium.com> > Message-ID: <000d01c50012$4ea49f30$4300000a@homeacxa7jw2xn> > Content-Type: text/plain; format=flowed;

When I use an analog phone connected to a Sipura SPA-2000 it takes about 3-4 seconds before the number is actually dialled. Very annoying especially if you are connecting an intercom to it. Can I change this behaviour and do I need to look at * config or the config of the SPA-2000? Thanks!

Been having a problem with my two Sipura 2000's dropping calls from the SPA-2000 side. Seems the calls are dropped right before the "Next Registration" time. Calls drop about ever 60 minutes or so. I have dialed from one port to the other and let it sit. After about 60 minutes or so the calls get dropped. System details are below Asterisk ver. CVS-HEAD-11/27/04-23:42:45 RHEL 3

Hello. Has anyone run into problems accessing voicemail with the Sipura SPA-2002's? Our SPA-2000's work fine (registers fine, able to make and receive calls properly & also able to access voicemail). We've configured the 2002's exactly the same way. However, with the SPA-2002 we're unable to access the voicemail system (though it does register fine and is able to

Hello, I am very new to asterisk and voip in general and so far have managed to get the FXO card and a few sip phones working fine. My question is where does the Sipura SPA 2000 come in the picture? Can it be used as an extension (i.e FXS) ? Or is it to be used as a line (i.e FXO)? Or it can be used as both? My understanding is that its just like another ATA186. Is that true? I guess what I

I heard Sipura had really awesome documentation on the SPA-2000 and SPA-3000, but you have to email them for it. When I did, they said I had to get it from a reseller. It's been a while since I bought my units, I don't even remember where or who they were bought from. Can somebody email me the documentation for these devices? I'm quite interested in knowing what every one of their 200+

I just got a refurb Sipura SPA-2000 and was able to assign it an IP address with DHCP and ping the device, but then I ran the firmware upgrade utility to bring it up to spa2k-2.0.13g which seemed to work just fine, but after it rebooted I cannot connect to its webserver for configuration. I can still ping the unit. When I use the built in voice menu it reads back the right IP address, webserver

I am looking at some lower cost phone to use with Asterisk. What is the ArtDio IPF-2000 or the Sipura SPA-841 like? Also, I see voipsupply.com has an ArtDio IPF-1000 listed, is this a new or an old model? I cannot find any information on it. Adi

I had a Grandstream 286 at my home hitting my Asterisk box at the office, all worked well and I received phone calls fine until the device just up and died. I replaced this unit with an SPA-2000 because I have been impressed with the Sipura devices and decided to use them for most of my needs in the future. Problem is that my phone attached to the device rings shortly after power up of the

Some people on this group may have understood from messages posted here that the Sipura SPA-2000 is not currently available for shipping. That is not the case. Voxilla.com has the Sipura SPA-2000 available for immediate shipping, and has had them since late November. The price is $109.95, and it comes with a month of free VoicePulse service with activation fees waived (a $65 value). In return

I have a Sipura SPA2000 2 line SIP FXS box with line 1 on port 5060 and line 2 on 5061. The SPA2000 is on IP address 192.168.17.6, and the asterisk box is on 102.168.17.2. Both SPA2000 ports(5060 and 5061) share the same IP address. Every minute I repeatedly get the following output: SIP Debugging Enabled 10 headers, 0 lines Reliably Transmitting: OPTIONS sip:192.168.17.6 SIP/2.0 Via:

I am located in the UK, and I am using Sipura spa-2000 adapters to connect analog phones to a voip network. The network connects to the PSTN as well via the Sipura spa-3000 adapter. I would like to provide surge protection for the spa-2000 and the spa-3000 adapters. 1. For spa-2000, fxs port: What is the maximum tip-to-ring voltage before damage to the the adapter occurs? 2. For spa-2000,

I figured out what was going on with the lack of/stuck on stuttered dial tone. Apparently, there are two voicemail directories being referenced: /var/spool/asterisk/voicemail/default, and /var/spool/asterisk/voicemail/local. The sip phones were using /var/spool/asterisk/voicemail/local to dump VM messages into, yet the MWI looks at /var/spool/asterisk/voicemail/default. Does anyone know why

I had everything working fine until today. Today the Sipura cannot dial anywhere. I just get the following: Feb 10 12:48:18 NOTICE[1205]: chan_sip.c:7399 handle_request: Unable to create/find channel Feb 10 12:48:19 NOTICE[1205]: chan_sip.c:7399 handle_request: Unable to create/find channel Feb 10 12:48:35 NOTICE[1205]: chan_sip.c:7399 handle_request: Unable to create/find channel Feb 10

If this has been covered before - I appologize. We use some Sipura SPA-2000's with the g711 codec and all seems fine (except for the occasional failure to register errors in my asterisk logs - but I will save that for another post). g711 call quality is on par with our Cisco 7960's. However, when using the g729 codec, the call quality on the Sipura device goes downhill on the PSTN side

I found a thread [1] last month about the poor/crappy g729 quality on Sipura units. Anyone noticed an improvement or the quality is still poor? If the Sipura firmware/g729 offers no quality yet, who else is offering a dual channel g729 ATA? I heard about Uniden, but I have no "reports" about their ATA... [1] Sipura g729 call quality to PSTN

Hi, the topic says it all really. Does the Sipura 3000 detect and report UK clid correctly? thanks Mike

When I dial a PSTN (via * with Digium Quad-E1) number, I hear two sumultaneous ring tones. One is coming from *, the other I assume is from the ATA. Is there an intelligent way to get around this?

Hi Friends, I have successfully implemented Intercom, Voicemail and International dialing using Asterisk. Now I want to connect my PSTN Lines to Asterisk server. I have 3 PSTN number (lines) to connect to Asterisk. For this, I want to use Sipura SPA-2100. Is my decession is correct or not? Is there any disadvantages with this Sipura SPA-2100? Please tell me. Thank you. Regards, Chandramouli

Hi all, Anyone able to remotely reboot their password protected Sipura SPA-3000 from command line. I am trying: Sipura SPA-3000 from command line: # wget http://admin:mypassword@192.168.1.55/admin/reboot The strange thing is it works fine when I go to http://admin:mypassword@192.168.1.55/admin/reboot with my web browser... Thanks....