Displaying 20 results from an estimated 6000 matches similar to: "TDM400 answers the line all the time!"
2006 Mar 21
2
TDM400 FXO module not answering or dialing out.
Hi all,
I have hit a wall configuring a TDM400, I have set these up before without
issue but today I just can't seem to figure out what I am doing wrong.
On an incoming call the following is produced in the Asterisk console with
verbose 4
-- Starting simple switch on 'Zap/2-1'
Mar 22 16:12:34 NOTICE[2051]: chan_zap.c:6063 ss_thread: Got event 18 (Ring
Begin)...
Mar 22
2006 Jan 31
3
ZAP <--> sip(polycom301) can not hear each other
please help!!!
I am dialing into our asterisk server(TDM400p) from the psnt. I hear our voicemail message and I press the extention 1000. The Polycom ip phone in the office rings. I pickup but neither side can hear one another. What have I done wrong?
thanks
sip.conf:
[general]
context=local-access ; Default context for incoming calls
bindport=5060
2007 Jan 22
1
2 ring delay before asterisk answer
I am a little green when it comes to all this but I am trying to connect
our PBX to an asterisk server using a TDM400 with 4 FXO modules. I am able
to dial an extension on my PBX handset and I get a dialtone from the PBX.
After 2 rings I then hear the asterisk server connect and I get a dialtone
from asterisk. I am then able to dial an extension on another asterisk
server.
My question is: How do
2003 Jun 23
1
Setting up the E100P
Hello,
I have an E100P, and in the zaptel.conf I have:
span=1,1,0,ccs,hdb4,crc4,yellow
fxsks=1-10
the light on the card is green( BTW what do all those states of the card
that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or
for the card?)
in the asterisks` zapata.conf I have:
[channels]
context=default
switchtype=euroisdn
signalling=fxs_ks
usecallerid=yes
hidecallerid=no
2005 May 05
3
can't create Zap channel
Before you jump ahead, yes I do have chan_zap.so loaded..
Call Flow: Asterisk 1 --IAX2--> Asterisk 2 ---> PRI
-- Accepting AUTHENTICATED call from 22.22.22.22:
> requested format = ulaw,
> requested prefs = (),
> actual format = ulaw,
> host prefs = (ulaw|alaw|gsm),
> priority = mine
-- Executing
2004 Mar 03
3
Ringing Delay
Sorry if this is a daft question but when a PSTN call comes in on my
X100P the console shows the following;
NOTICE[1217602880]: File chan_zap.c, Line 4456 (ss_thread): Got event 2
(Ring/Answered)...
NOTICE[1217602880]: File chan_zap.c, Line 4456 (ss_thread): Got event 2
(Ring/Answered)...
NOTICE[1217602880]: File chan_zap.c, Line 4456 (ss_thread): Got event 2
(Ring/Answered)...
2007 Aug 02
1
A simple IVR extension problem
Hi list,
I am running TDM11b + Asterisk-1.4.9 + Zaptel-1.4.4 + Libpri-1.4.1 on CentOS
5.
I am having trouble to make my simple IVR extension work, here is relevant
config:
zapata.conf
----
context=incoming
signalling=fxs_ks
channel => 4
context=internal
signalling=fxo_ks
channel => 1
-----
extensions.conf:
----
[office]
exten => s,1,Dial(Zap/1,30)
[home]
exten =>
2005 Aug 01
1
X100P/Caller ID: clidtest works, * complains [repost]
Hi,
I'm running Asterisk 1.0.8 on Gentoo, with an X100P (clone) card, and I'm
having problems with Caller ID. I have run clidtest, and it seems happy
enough, returning:-
server clidtest # ./clidtest /dev/zap/1
Number: 0412222222, Name: MOBILE
(that number's fake.) However, I'm not getting the caller ID passed
through with *. Sometimes I get a "failed checksum" like
2007 Apr 09
4
incoming zaptel calls fail
Using the latest SVN of zaptel and asterisk, I can no longer receive
incoming analog calls. The caller just hears it ringing but Asterisk
doesn't pick up.
I am seeing these error messages:
[Apr 9 09:38:02] WARNING[16564]: chan_zap.c:6470 ss_thread: CallerID
returned with error on channel 'Zap/2-1'
[Apr 9 09:38:50] WARNING[16570]: chan_zap.c:6470 ss_thread: CallerID
2007 Nov 20
1
FXO Hangs up automatically
Hi,
I'm having problems using a TDM400P Card. I put my SIM card in a Nokia
Premicell and connected it to a TDM400P card but when I make calls to
the number, it hangs up automatically. The card also can't call out.
Any ideas? I've searched the archives without much success. I
appreciate all your help.
Details:
I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an
2005 Jul 22
1
X100P not answering
I have an Asterisk server running todays CVS (updated it just in case
that was the problem). It has 3 X100P cards. The first two lines I use
as my normal work lines and the third is my fax line which I use with
SpanDSP. I run Fedora Core 4.
I have a problem that the third X100P does not answer the call. From
the console I can see that there is an incoming call with the following:
--
2004 Sep 28
7
UK (British Telecom) Caller ID again
I've followed the recent thread on caller id with UK British Telecom
networks (where the caller id data is delivered before the first ring).
My understanding is that if I use a recent CVS head (e.g.
CVS-HEAD-09/18/04-17:45:52) and a TDM400 with FXO modules, all I need to
do is include the line:
usecallerid=uk
In my zapata.conf (in the [channels] section)
I've done this, but I get:
Sep
2005 Feb 03
1
Mi extensions keeps ringing
Hi asterisk users, I have a inssue with incoming calls with wcfxo card,
while receiving a call, I?ve configured my dialplan to forward the call to
all mi home voip extensions and that works just fine, but while in the call,
after a few seconds, the pbx starts the simple switch once more and keeps
ringing the voip extensions
log as follows:
2009 Jun 14
2
FXS - TDM400 - No dial tone
I have a TMD400 card installed in a PC with one fxs (installed in slot
2) and two fxos (installed in slots 3 & 4).? fxos work fine but I am
unable to get a dial tone for any devices connected to the fxs.? I
have correctly connected the power supply to the card and I have even
tried moving the card from slot 1 to 2 on the board.
Below is from the console when I try to route a call from FXO on
2007 Feb 08
1
TDM400 with 1 FXO
Hi All,
I cannot get my TDM to work correctly.
In my /etc/zaptel.conf file I have
loadzone = us
defaultzone=us
fxoks=1
In my /etc/asterisk/zapata.conf file I have
[trunkgroups]
[channels]
context=from-pstn
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
2005 Oct 08
2
Configuring TDM400 in Australia
Hi, all
I have installed TDM400 with 1 FXS and 1 FXP ports.
Now I am goig through documentation on how to configure it.
It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do
I use?
Can someone send me sample zaptel.conf file for Australia? This will save me
some time and will be used as a working example.
Thanks,
Rudolf
2007 Jul 01
1
Asterisk strange behaviour
Hi all
I?m a newbie to asterisk and I have install and configure asterisk 1.4.5
I have made some test and have face a strange behaviour
I hava a simple dialplan when a call is receive from PTSN,
[PSTN]
exten => s,1,Answer()
exten => s,2,Playback(intro-sicx) ; Listen to your voice
exten => s,3,Dial(SIP/steph)
exten => s,4,Hangup()
I got the following when a call is
2006 May 17
1
TDM does not disconnect
Hello all.
This is my very first message to the list. I have a TDM400P card, It
has 2 FXO channels which are connected to extensions of my PBX
(Ericsson BP250), so I can dial from any SIP softphone directly to
physical (analog and digital) extensions on my company.
My PBX is configured so when I dial 8 on any extension, it will
redirect to the first free FXO channel on my TDM400P card.
2005 Sep 12
2
Callerid fails in any release after beta1 fails
I have 1 x100p. Caller id works fine with the beta1 release. Cvshead
releases fail with a combination of checksum and ss_thread errors?
I'm concerned when beta2 or the 1.2 release comes out it will not work.
I have been through the configs I can't find and changes that need to be
made to get CVSHEAD to work.
Thanks
John Hill
2008 Mar 27
1
Asterisk not picking up (some) calls due to zaptel detecting and clearing alarms
Hi All,
For the most part, the PBX works as it should. Occasionally people complain
that they call and the PBX doesn't pick up. Other times it looks like the
call is answered by Asterisk but I still hear ringing and I start listening
to the IVR menu a few seconds into it.
As for Asterisk not picking up, I see the following in the logs:
[Mar 27 13:32:29] NOTICE[13197]: chan_zap.c:7071